OESF Portal | OESF Forum | OESF Wiki | LinuxPDA | ELSI (coming soon) | Ibiblio

IPB

Welcome Guest ( Log In | Register )


0laf
Posted on: Nov 2 2008, 07:00 AM





Group: Members
Posts: 4
Joined: 16-September 07
Member No.: 20,407


QUOTE(utx @ Nov 2 2008, 03:02 PM) *
Please try netmask 255.255.255.0. I am surprised, that netmask 255.255.255.255 from my example was ever working.

Thx for helping me, i changed the netmask to 255.255.255.0, but it didnt work huh.gif Which version of angstrom are you using?
  Forum: Angstrom & OpenZaurus · Post Preview: #180298 · Replies: 6 · Views: 7,230

0laf
Posted on: Nov 2 2008, 05:02 AM





Group: Members
Posts: 4
Joined: 16-September 07
Member No.: 20,407


QUOTE(utx @ Nov 1 2008, 10:09 PM) *
You have bad configuration. You are configuring ifconfig with a different network address than route (101 x 201).

Here are my files:

Manual setup

ifcfg-usb0 for automatic setup in openSUSE

Thanks for your reply, I tried your script, but usb networking is still not possible for me sad.gif
Now my config looks like that:
desktop:
ifconfig:
CODE
eth5 Link encap:Ethernet HWaddr 00:90:27:54:0E:D5
inet addr:192.168.1.10 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::290:27ff:fe54:ed5/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:30073 errors:0 dropped:0 overruns:0 frame:0
TX packets:26165 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:30927764 (29.4 MiB) TX bytes:2415453 (2.3 MiB)

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:589 errors:0 dropped:0 overruns:0 frame:0
TX packets:589 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:61128 (59.6 KiB) TX bytes:61128 (59.6 KiB)

usb0 Link encap:Ethernet HWaddr DE:3A:E8:4A:93:2C
inet addr:192.168.129.1 Bcast:192.168.129.255 Mask:255.255.255.255
inet6 addr: fe80::dc3a:e8ff:fe4a:932c/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:96176 dropped:0 overruns:0 frame:0
TX packets:6 errors:501 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 cool.gif TX bytes:468 (468.0 cool.gif

route - n:
CODE
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
192.168.129.201 0.0.0.0 255.255.255.255 UH 0 0 0 usb0
192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth5
0.0.0.0 192.168.1.252 0.0.0.0 UG 0 0 0 eth5


zaurus:
ifconfig:
CODE
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:1739 errors:0 dropped:0 overruns:0 frame:0
TX packets:1739 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:191760 (187.2 KiB) TX bytes: 191760 (187.2 KiB)

usb0 Link encap:Ethernet HWaddr 6A:67:78:C5:07:1B
inet addr:192.168.129.201 Bcast:192.168.129.255 Mask:255.255.255.255
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:30 errors:0 dropped:0 overruns:0 frame:0
TX packets:24 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1906 (1.8 KiB) TX bytes:756 (756.0 cool.gif

route - n:
CODE
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
192.168.129.1 0.0.0.0 255.255.255.255 UH 0 0 0 usb0
0.0.0.0 192.168.129.1 255.255.255.255 UG 0 0 0 usb0


i hope you can help me, that would be great
  Forum: Angstrom & OpenZaurus · Post Preview: #180296 · Replies: 6 · Views: 7,230

0laf
Posted on: Nov 1 2008, 11:25 AM





Group: Members
Posts: 4
Joined: 16-September 07
Member No.: 20,407


Hello all,

at the moment I m trying to get USB networking configured for the Zaurus CL1000.
The Zaurus is running Angstrom x11-image 2007.12-r18.

Basically I tried to get it working by performing the steps which are described in the USB networking howto on the Angstrom wiki (http://linuxtogo.org/gowiki/AngstromManual)...
Nevertheless its not working for me blink.gif

I did following on the zaurus:
  • modprobe g_ether
  • ifconfig usb0 192.168.1.201 netmask 255.255.255.255 up
  • route add -host 192.168.1.101 usb0
  • then i had a look at the available network devices with ifconfig, interface "usb0" seemed to be fine

Next I continued with the configuration of the desktop computer (running debain etch 4.0 stable):
  • loaded the modules cdc_ether and usbnet
  • dmesg output:
    usb0: register 'cdc_ether' at usb-0000:00:08.1-2, CDC Ethernet Device, de:3a:e8:4a:93:2c
  • lsusb output:
    Bus 002 Device 010: ID 0525:a4a2 Netchip Technology, Inc. Linux-USB Ethernet/RNDIS Gadget
  • ifconfig usb0 192.168.1.101 netmask 255.255.255.255 up
  • route add -host 192.168.1.201 usb0
  • ifconfig output:

    usb0 Link encap:Ethernet HWaddr DE:3A:E8:4A:93:2C
    inet addr:192.168.1.101 Bcast:192.168.1.255 Mask:255.255.255.255
    inet6 addr: fe80::dc3a:e8ff:fe4a:932c/64 Scope:Link
    UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
    RX packets:0 errors:108772 dropped:0 overruns:0 frame:0
    TX packets:6 errors:288 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:1000
    RX bytes:0 (0.0 b ) TX bytes:468 (468.0 b )
Well next I tried to test the connection with ping:
on the desktop: ping 192.168.1.101 -> ok, ping 192.168.1.201 -> not working
zaurus: ping 192.168.1.201 -> ok, ping 192.168.1.101 -> not working

Hm, obviously there is something wrong with my configuration sad.gif

I m somewhat stuck, any help would be greatly appreciated

Thanks in advance
olaf
  Forum: Angstrom & OpenZaurus · Post Preview: #180285 · Replies: 6 · Views: 7,230

0laf
Posted on: Sep 24 2007, 06:34 AM





Group: Members
Posts: 4
Joined: 16-September 07
Member No.: 20,407


Hi all,

recently my dad purchased a Zaurus sl-c1000 and told me to install something more useful on it biggrin.gif
This is what i wanted to get working on the Zaurus:

-simple windowmanager (fluxbox, blackbox,fvwm)
-multiuser setup
-native development (fortran, c++)
-programs like xpdf, gnumeric
-properly suspend

Until now I ve tried out the last version of OZ with gpe, pdaXrom and pdaXiirom

On both, pdaXrom and pdaXiirom, suspend has been a problem. Not sure why,
Is that a common problem with those Roms?

The last Rom i installed, has been OZ.
Suspending and multiuser setup works very well. I even managed to get gcc working.
Next I installed blackbox because i wanted something more useful than gpe rolleyes.gif
but it wasnt working because of the disabled colormanagement in X11. (i tried to recompile x11 with colormanagement enabled, but no success)

Which Rom would you suggest me to use? Is angstrom a try worth?

Thanks in advance
olaf
  Forum: Software · Post Preview: #167871 · Replies: 5 · Views: 3,288


New Posts  New Replies
No New Posts  No New Replies
Hot topic  Hot Topic (New)
No new  Hot Topic (No New)
Poll  Poll (New)
No new votes  Poll (No New)
Closed  Locked Topic
Moved  Moved Topic
 

RSS Lo-Fi Version Time is now: 22nd November 2017 - 07:08 AM