OESF | ELSI | pdaXrom | OpenZaurus | Zaurus Themes | Community Links | Ibiblio

IPB

Welcome Guest ( Log In | Register )

3 Pages V  < 1 2 3  
Reply to this topicStart new topic
> Sl-7500c 128m Flash Upgrade Failed!, Is there still hope?
scholbert
post Dec 1 2006, 06:28 AM
Post #31





Group: Members
Posts: 48
Joined: 21-November 05
Member No.: 8,576



QUOTE(albertr @ Dec 1 2006, 03:19 AM)
QUOTE(scholbert @ Nov 28 2006, 05:55 PM)

In an older post albertr mentioned he got nothing valid out of the serial lines on his C1000.


No, I never said that. In fact, I posted many times on this (and other forum) that serial UART lines are available on Sharp I/O port on 1000/3x00 Zaurii. They are logical 3V TTL levels, so need RS232 tranceiver. In fact, I'm using it on my C1000 with Sharp serial cable quite often.

There's no JTAG lines on Sharp I/O port on 1000/3x00 AFAIK.
-albertr
*



Hi albertr,

i'd really like to apologize for my statement rolleyes.gif .
I didn't remember the exact post as i wrote these lines and i thought it was you who once mentioned kind a thing. Blame on me sad.gif

Never ever i'll write something down again, if i do not exactly know where i got it from.
At least i wanted to point out that there were many different opinions about the serial stuff and I/O connector.

But it seemed that i was the only one confused blink.gif !

Perhaps this is a good moment for me to send a personally "thank you, albertr".
It amazing what you have done so far and what information you put down into this forum!

Let me go back to the topics.

guylhem may be right.
I think there could be some kind of gate logic inside C1000/3x00, which is activated with pin 13 and maps the JTAG lines to the pins 5,6,7 and 14 on the I/O connector.

I will do some investigation. Unfortunately i got no schematic of the device.

scholbert
Go to the top of the page
 
+Quote Post
albertr
post Dec 1 2006, 11:13 AM
Post #32





Group: Members
Posts: 535
Joined: 7-March 04
Member No.: 2,195



No problem, I just wanted to set the record streigth.

If I'm not mistaken, Guylhem probably mentioned the older models, not pxa270-based C1000/3x00....
Thanks.
-albertr
Go to the top of the page
 
+Quote Post
pelrun
post Dec 1 2006, 06:32 PM
Post #33





Group: Members
Posts: 369
Joined: 6-September 04
From: Brisbane, Australia
Member No.: 4,488



The 3100 schematic definitely provides for JTAG wired to behave as scholbert says: holding pin 13 high remaps 5 as TDI, 6 as TMS, 7 as TDO, 14 as TCK.

Unfortunately it looks like all the components in that circuit have been left off the production board, as one of albertr's nice highres photos of the board shows unpopulated chip positions right where I'd expect to see the two TC7WB66FK bus select chips, and the schematic has all the components in that part of the circuit marked as "OPEN". sad.gif
Go to the top of the page
 
+Quote Post
scholbert
post Dec 3 2006, 02:10 PM
Post #34





Group: Members
Posts: 48
Joined: 21-November 05
Member No.: 8,576



Hi pelrun,

great information. I thought it would be like that.
I just quoted your posting in the C1000/3x00 Hardware section.

Just for completion of the information about the I/O connector.
I hope it's O.K. for you that way!

Perhaps this could be very helpful to those who are interested in upgrading flash or (un)bricking their device completely rolleyes.gif !

Greets,

scholbert
Go to the top of the page
 
+Quote Post

3 Pages V  < 1 2 3
Reply to this topicStart new topic
2 User(s) are reading this topic (2 Guests and 0 Anonymous Users)
0 Members:

 



RSS Lo-Fi Version Time is now: 21st November 2014 - 09:52 AM