OESF | ELSI | pdaXrom | OpenZaurus | Zaurus Themes | Community Links | Ibiblio

IPB

Welcome Guest ( Log In | Register )

 
Reply to this topicStart new topic
> Sl-5500 Cradle Issues, powered cradle kill usb connection
_dark_
post Feb 21 2011, 01:34 PM
Post #1





Group: Members
Posts: 19
Joined: 14-July 05
From: Croatia
Member No.: 7,596



Hi guys!

Is it normal that when colie put in cradle and power, he lose usb conection with windows, but when disconect cradle from power -> i can conect normaly to desktop pc via usb?
Is it posible that some caps or something burned in cradle?

Thanx!
Go to the top of the page
 
+Quote Post
sdjf
post Mar 22 2012, 04:27 AM
Post #2





Group: Members
Posts: 454
Joined: 17-November 05
Member No.: 8,551



Your ROM could be a factor. This is tkcROM you have on the Collie?

Try running the following commands, both when Collie is and is not connected, and before and after attach cradle to power supply.

route

ifconfig -a

That can help debug what is going on. It is possible you may have to reconfigure from command line to get connection recognized.

Post results, they may be helpful to figure it out and get suggested solutions.

sdjf
Go to the top of the page
 
+Quote Post
_dark_
post Mar 30 2012, 04:55 PM
Post #3





Group: Members
Posts: 19
Joined: 14-July 05
From: Croatia
Member No.: 7,596



Rom is sharprom, but the same issue is with kompanyROM
Output with cradle connection, and without power
CODE
# route
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
192.168.129.0   *               255.255.255.0   U     0      0        0 usbd0
default                         0.0.0.0         UG    0      0        0 usbd0
# ifconfig -a
irda0     Link encap:IrLAP  HWaddr 00:00:00:00
          NOARP  MTU:2048  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:8
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
          Interrupt:16

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:275 errors:0 dropped:0 overruns:0 frame:0
          TX packets:275 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:21996 (21.4 Kb)  TX bytes:21996 (21.4 Kb)

usbd0     Link encap:Ethernet  HWaddr 40:00:01:00:00:01
          inet addr:192.168.129.201  Bcast:192.168.129.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:173 errors:1 dropped:1 overruns:0 frame:1
          TX packets:125 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:100
          RX bytes:18356 (17.9 Kb)  TX bytes:33470 (32.6 Kb)

#

Output with cradle connection, and power -> ..as when i connect power immediately connection disapear and windows report under device manager "This device cannot start. (Code 10)"

Output without cradle and power connected:
route
empty

ifconfig -a same such as with cradle, but whitout usbd0 connection

(I dont know comand in console to redirect output in file)
Go to the top of the page
 
+Quote Post
sdjf
post Mar 31 2012, 08:28 PM
Post #4





Group: Members
Posts: 454
Joined: 17-November 05
Member No.: 8,551



Which Sharp ROM? I use 2.38 and have never seen a device manager.

Have you tried simply restarting the usbd0 connection after plugging power in?

Command would be something like:

ifconfig usbd0 192.168.129.201 netmask 255.255.255.0 up

Also, are you sure that 192.168.129.201 is the right IP? I still get very confused about figuring out the right one, but maybe somebody else can help who knows more.

Meanwhile, try the above ifconfig command, and right after that, try your ifconfig -a

sdjf
Go to the top of the page
 
+Quote Post

Reply to this topicStart new topic
2 User(s) are reading this topic (2 Guests and 0 Anonymous Users)
0 Members:

 



RSS Lo-Fi Version Time is now: 21st December 2014 - 06:25 AM