OESF | ELSI | pdaXrom | OpenZaurus | Zaurus Themes | Community Links | Ibiblio

IPB

Welcome Guest ( Log In | Register )

 
Reply to this topicStart new topic
> Zaurus Jtag Cable
puffy
post Jan 25 2008, 07:59 PM
Post #1





Group: Members
Posts: 21
Joined: 11-August 06
From: NY
Member No.: 10,762



Does anyone here have experience using a Jtag cable for fixing a bricked Zaurus?
I am interested in knowing where to get the 18 pin connector to make a jtag cable.
Go to the top of the page
 
+Quote Post
pelrun
post Jan 25 2008, 09:42 PM
Post #2





Group: Members
Posts: 369
Joined: 6-September 04
From: Brisbane, Australia
Member No.: 4,488



How did you manage to brick it? A bad flash is *not* sufficient; the fn-D-M key combo will still get you into the diagnostic menu (it's stored in ROM.)

In any case, the jtag support is incomplete - it's in the schematic but the necessary components are not present on the actual units.
Go to the top of the page
 
+Quote Post
puffy
post Jan 26 2008, 12:13 AM
Post #3





Group: Members
Posts: 21
Joined: 11-August 06
From: NY
Member No.: 10,762



QUOTE(pelrun @ Jan 25 2008, 09:42 PM) *
How did you manage to brick it? A bad flash is *not* sufficient; the fn-D-M key combo will still get you into the diagnostic menu (it's stored in ROM.)

In any case, the jtag support is incomplete - it's in the schematic but the necessary components are not present on the actual units.



Everyone tells me the diag menu is in read only memory. But I guess you can screw up the ability to access it. Because I have thoroughly exhausted every conceivable and documented procedure to access said menu(s).

Leave it to me to be the only freekin' schmuck who actually somehow bricked his Zaurus. Well, I didn't do it but the lame eBay guy who sold it to me did. The menus were never functioning.

Anyone know of a good repair service?
Go to the top of the page
 
+Quote Post
pelrun
post Jan 26 2008, 02:48 AM
Post #4





Group: Members
Posts: 369
Joined: 6-September 04
From: Brisbane, Australia
Member No.: 4,488



Actual physical or electrical damage is really the only way to brick the Z; since you weren't the one who broke it then what happened is anybody's guess - a fall, water ingress, voltage spike etc.

If the seller represented it as a working unit then you should be able to claim back your money...

(oh, and as for last resorts, you *can* jtag the Z, but it requires opening the unit up and soldering to the signals directly - the missing components just remove the ability to use the connector to do it non-invasively.)
Go to the top of the page
 
+Quote Post
puffy
post Jan 26 2008, 06:14 AM
Post #5





Group: Members
Posts: 21
Joined: 11-August 06
From: NY
Member No.: 10,762



QUOTE(pelrun @ Jan 26 2008, 02:48 AM) *
Actual physical or electrical damage is really the only way to brick the Z; since you weren't the one who broke it then what happened is anybody's guess - a fall, water ingress, voltage spike etc.

If the seller represented it as a working unit then you should be able to claim back your money...

(oh, and as for last resorts, you *can* jtag the Z, but it requires opening the unit up and soldering to the signals directly - the missing components just remove the ability to use the connector to do it non-invasively.)



Too late for a claim.
Going to get out the iron and make some solder smoke. I've already gathered quite a few useful documents to help. But none yet that detail what needs to be connected. I'm now using a Simpad SL4 I bought to ease the pain tongue.gif
But I'm fixing the Zaurus.
Go to the top of the page
 
+Quote Post
pelrun
post Jan 26 2008, 08:11 AM
Post #6





Group: Members
Posts: 369
Joined: 6-September 04
From: Brisbane, Australia
Member No.: 4,488



I'd give you a copy of the service manual, but I was asked not to distribute it. Sorry. sad.gif

Doesn't mean I can't point stuff out on a picture biggrin.gif I've left the usb port in for orientation purposes.

I've marked two of the JTAG testpoints; but I can't see from the photo I used where the testpoints are for the other two. So the diagram points to the appropriate IC pads instead. As far as the other components go, there's missing pullup/pulldown resistors for TCK, which I've marked as they're probably important; and missing caps to ground for TDI, TMS and TCK which I haven't marked as they're probably less important (I don't know the values either.)

Edit: uhoh - on the schematic the jtag wires are also crossed out at the cpu end. I hope they're still connected...

Attached File(s)
Attached File  zjtag.JPG ( 93.85K ) Number of downloads: 76
 
Go to the top of the page
 
+Quote Post
puffy
post Jan 26 2008, 11:55 AM
Post #7





Group: Members
Posts: 21
Joined: 11-August 06
From: NY
Member No.: 10,762



QUOTE(pelrun @ Jan 26 2008, 08:11 AM) *
I'd give you a copy of the service manual, but I was asked not to distribute it. Sorry. sad.gif

Doesn't mean I can't point stuff out on a picture biggrin.gif I've left the usb port in for orientation purposes.

I've marked two of the JTAG testpoints; but I can't see from the photo I used where the testpoints are for the other two. So the diagram points to the appropriate IC pads instead. As far as the other components go, there's missing pullup/pulldown resistors for TCK, which I've marked as they're probably important; and missing caps to ground for TDI, TMS and TCK which I haven't marked as they're probably less important (I don't know the values either.)

Edit: uhoh - on the schematic the jtag wires are also crossed out at the cpu end. I hope they're still connected...


Sweet laugh.gif
Thank you pelrun
Go to the top of the page
 
+Quote Post
Hrw
post Jan 31 2008, 11:52 PM
Post #8





Group: Members
Posts: 1,376
Joined: 11-January 04
From: Poznań, Poland
Member No.: 1,413



http://blog.haerwu.biz/2006/08/09/sharp-zaurus-jtag-cable/ is schematics of official Sharp Zaurus JTAG cable. It is from SL-5500 service manual and require Win32 JTAG tool.

And I can not get it how you were able to brick sl-cxx00 device... From what I know only collie (5000/5500) can be bricked - rest of Zaurus devices warrant entry to diagnostics where nand restore is available.
Go to the top of the page
 
+Quote Post
scholbert
post Feb 1 2008, 04:45 AM
Post #9





Group: Members
Posts: 48
Joined: 21-November 05
Member No.: 8,576



Hi there,

very nice pic pelrun rolleyes.gif

I once started a thread with a similar question (pelrun might remember...):
http://www.oesf.org/forum/index.php?showtopic=22106

These informations may also be very useful for some of you tongue.gif

scholbert
Go to the top of the page
 
+Quote Post

Reply to this topicStart new topic
2 User(s) are reading this topic (2 Guests and 0 Anonymous Users)
0 Members:

 



RSS Lo-Fi Version Time is now: 2nd October 2014 - 02:27 AM