How-TO: Connet CF GPRS/GSM (AudioVox RTM8000) to internet Options

[gummy_bear]

Hi all, I know this thread is old but i am desperate. I have a gumstix from www.gumstix.com, linux 2.6 ARM etc.

I have put an Audiovox RT-8000 in it but it is not going to work without a fight so I need your help. I will not bore you with too much gorry detail which is not required because I have just found the serial_cs.o module here, the problem is I try to load the module and it says

"insmod: error inserting './serial_cs.o': -1 Invalid module format"

The irq allocation for the card is totally messed up so I really need this patch.

cat /proc/tty/driver/serial
serinfo:1.0 driver revision:
0: uart:16C950/954 port:C4860400 irq:49 tx:169 rx:0 CTS
1: uart:unknown port:00000000 irq:0
2: uart:unknown port:00000000 irq:0
3: uart:unknown port:00000000 irq:0

# cat /proc/tty/drivers
/dev/tty /dev/tty 5 0 system:/dev/tty
/dev/console /dev/console 5 1 system:console
/dev/ptmx /dev/ptmx 5 2 system
serial /dev/ttyS 4 64-67 serial
PXA serial /dev/ttySA 4 68-71 serial
pty_slave /dev/pts 136 0-1048575 pty:slave
pty_master /dev/ptm 128 0-1048575 pty:master

No 49 irq is used by the serial :-(
seems like 8250.ko should be patched :-(

# cat /proc/interrupts
CPU0
0: 44 SC HWUART
4: 0 SC pxa2xx_udc
18: 0 SC DMA
19: 68485 SC PXA Timer Tick
27: 0 GPIO CF0 nSTSCHG
34: 0 GPIO CF0 nCD
58: 0 GPIO pxa2xx_udc
59: 1778 GPIO eth0
Err: 0

I am a noob having a love/hate relationship with linux at the moment, can someone guide me to the light?

Thanks
Chris

[zmiq2]

I think that the seerial_cs.o module you got from somewhere is for kernel 2.4, thus completely unusable under 2.6.

maybe if using 2.6, the serial_cs.ko (the module naming in 2.6 is .ko) that is already with the distribution you are using could work.

1) Do you have a serial_cs module from the same place you got 2.6 kernel? Can you modprobe that module ?

If so, I'd suggest to go ahead and after, send the setserial command.

HTH

[speculatrix]

yeah, I would agree that it sounds like a module mismatch. Be sure to use the same kernel source throughout and also to make sure the kernel versioning is correct in the main Makefile.

[gummy_bear]

ok so it is all down to 8250.ko module, it needs to be modified. oh my god this is hard work for me, I am dumbass!

it needs support for irq49 or something like that, how does a module get compiled? Where is the source

[zmiq2]

Hi,

I'd suggest

1) ask someone in a gumstix forum o mailing list to have it compiled for you

2) install a virtual machine with all the gumstix development tools installed, and go compile yourself ...

The source is probably somewhere the linux 2.6 modules sources.

[Viss]

This doesnt work for me, but I found this article useful:

http://tuxmobil.org/pcmcia_cf_anycom_gprs.html

... and now I am connected

I dont know what change take effect, but this:

CODE

noauth
connect "/usr/sbin/chat -v -f /etc/chatscripts/provider"
defaultroute
/dev/ttyS0
115200
nocrtscts
lock
noipdefault
debug
user fasel

and this:

CODE

ABORT BUSY
ABORT "NO CARRIER"
ABORT VOICE
ABORT "NO DIALTONE"
"" ATZ
OK AT+CPIN="<PIN>"
OK AT+CGDCONT=1,"IP","<APN>"
OK ATDT*99***1#
'CONNECT' '\c'
'TIMEOUT' '5'

are WORKING on SL-C1000 (pdaXii13 build5.4.9 "Sally" with kkazakov13 libraries and some from pdaXii13v2)

But thanx anyway, because this post inspired me and was the first thing when I was looking where to start.

Hope my post help anybody with same trouble ;-)