Socket Bluetooth Cf Card Not Working (surprise!), 2or0's rootfs & 2.6.24.4 kernel Options

[Khepri]

Installed bluez etc. Drivers won't load.


dmesg:

Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.9
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8


and when I take the card out and reinsert it:

pccard: card ejected from slot 1
pccard: PCMCIA card inserted into slot 1
pcmcia: registering new device pcmcia1.0


Tried playing around with hciattach and setserial, with no success.

Is this an issue with the kernel? I read about a bug (here and elsewhere) in 2.6 kernels that prevents some Socket BT cards from working, but I'm not really up to configuring a kernel for my Z from scratch, not knowing every relevant switch I should temper with in the config.

Any ideas?


Here's some output:

Zaurus:~# hciattach /dev/ttyS4 socket
Can't get port settings: Input/output error
Can't initialize device: Illegal seek

[Khepri]

Rebooted and serial_cs drivers were loaded for the Socket BT card.

I'm not used to rebooting, I run a freakin' Linux after all!

[Khepri]

I am stuck again.

I execute "rfcomm connect 0 <bdaddr>".
The phone asks if I want to bond with the Z, I say Yes.
I enter the same pin code on the phone that I have in /etc/bluetooth/hcid.conf
The phone says "Verifying PIN... Please Wait".

A couple seconds pass, the connection fails and Z says:

Can't connect RFCOMM socket: Operation now in progress

Why!?

[Khepri]

Just reporting in that I got it to work.

It was an issue with HALd not loading correctly at boot because it hadn't loaded dbus first.
I also had to install the passkey-agent and run the process in the background while binding the devices.

Then I did:

hciattach /dev/ttyS4 socket
hciconfig hci0 up
rfcomm connect rfcomm0

I had so many different problems during setting this up that if I can gather some energy I will write a thorough tutorial on it.

[ant]

This should be valid for debian too:

/etc/sysconfig/bluetooth
BLUETOOTH=yes
BLUETOOTH_PORT=/dev/ttyS4
#BLUETOOTH_SCRIPT=
BLUETOOTH_SPEED=230400
BLUETOOTH_PROTOCOL=bcsp
#
#
#BLUETOOTH_SPEED=921600
#BLUETOOTH_PROTOCOL=socket

/etc/rfcomm.conf
# RFCOMM configuration file.
#

rfcomm0 {
# # Automatically bind the device at startup
bind yes;
#
# # Bluetooth address of the device
device 00:xx:xx:xx:xx:xx;

#
# # RFCOMM channel for the connection
channel 1;
#
# # Description of the connection
comment "My Nokia xxxx";
}

rfcomm1 {
bind yes;
device 00:xx:xx:xx:xx:xx;
channel 1;
comment "My BT-GPS-xx";
}


Then, but this is using Angstrom, rfcomm is not pulled automatically though bind=yes, so add the two calls in

/etc/init.d/bluetooth

start)
...
rfcomm bind all

stop )
...
rfcomm release all

[Raul]

#I had so many different problems during setting this up that if I can gather some energy I will write a thorough tutorial on it.
Could you? I had many problems myself and it didn't work.
Which version is your card?

[alexl]

I have a Bluetooth CF card on Angstrom on SL-C860.

ant, thanks for your script as it was enough to get my card working. I have no idea what manufacturer the card is - it doesn't return an ID, other than 'Bluetooth CF card', when I do 'pccardctl ident'.

This worked though:

CODE

modprobe serial_cs
modprobe hci_uart
hciattach -s 115200 /dev/ttyS4 socket 230400
hciconfig hci0 up

Perhaps I should post this on an Angstrom forum but it's late in the day and I am dozing off at the keyboard.

Lex

[HRH_H_Crab]

O.K.

I too have managed to get things working.
It's a lot better than my bluetooth dongle was, doesn't flap around all over the place.
One thing though, I cant seem to get it working after a suspend without a reboot.
Is there a trick to this that anyone knows?

[HRH_H_Crab]

Figured it out.
killall hciattach to sort out the hciattach, and pccardctl eject 1 to eject the card safely.

[pelrun]

I modified my apm suspend/resume scripts to eject/insert the card automatically; it seems to work fairly well.

[HRH_H_Crab]

Wicked idea!
I'll look in to this and see if I can figure it out.