OESF | ELSI | pdaXrom | OpenZaurus | Zaurus Themes | Community Links | Ibiblio

IPB

Welcome Guest ( Log In | Register )

 
Reply to this topicStart new topic
> Pdaxrom Not Loading Sd Or Cf, What happened?
Dima202
post May 16 2006, 06:10 PM
Post #1





Group: Members
Posts: 68
Joined: 6-November 05
Member No.: 8,479



Interesting, I was just sitting there trying to make zpsx to work. Then I rebooted the Zaurus when it came on neither the CF or SD started. I went to aterm typed in reboot. It is stuck on line "INIT: no more processes left in tis runlevel" and that's it! It's just stuck there. I tried taking out battery, leaving zaurus dry for a few minutes. Turned on, same thing. Tested SD card in sd reader, reads it fine. CF card is a Symbol wifi card.
Anyone know what happened:(? Maybe there is a way to manually make it run? sad.gif sad.gif sad.gif

Thanks in advance! sad.gif

-My poor Z ohmy.gif

---Update: Also when it boots after I manually power off it says: "Inode #6581 was a directory with children - removing these too..." Children? Shoud I be worried? dry.gif
----Update: There is like 10 lines of these with different Inode numbers.
----Update: No the light on the Symbol card doesn't light up on boot, or when in startx.
----Update: Found that in /dev/ there is no mmcd????? This isn't right! right?
Go to the top of the page
 
+Quote Post
karlto
post May 16 2006, 07:58 PM
Post #2





Group: Members
Posts: 343
Joined: 3-October 05
From: NZ
Member No.: 8,243



QUOTE(Dima202 @ May 17 2006, 03:10 PM)
Interesting, I was just sitting there trying to make zpsx to work. Then I rebooted the Zaurus when it came on neither the CF or SD started. I went to aterm typed in reboot. It is stuck on line "INIT: no more processes left in tis runlevel"  and that's it! It's just stuck there. I tried taking out battery, leaving zaurus dry for a few minutes. Turned on, same thing. Tested SD card in sd reader, reads it fine. CF card is a Symbol wifi card.
Anyone know what happened:(? Maybe there is a way to manually make it run? sad.gif  sad.gif  sad.gif

Thanks in advance! sad.gif

-My poor Z ohmy.gif

---Update: Also when it boots after I manually power off it says: "Inode #6581 was a directory with children - removing these too..." Children? Shoud I be worried? dry.gif
----Update: There is like 10 lines of these with different Inode numbers.
----Update: No the light on the Symbol card doesn't light up on boot, or when in startx.
----Update: Found that in /dev/ there is no mmcd????? This isn't right! right?
*

Do you have a console? Try checking the filesystems on the cards - e.g. e2fsck if ext2 formatted.
Go to the top of the page
 
+Quote Post
Dima202
post May 16 2006, 08:06 PM
Post #3





Group: Members
Posts: 68
Joined: 6-November 05
Member No.: 8,479



QUOTE(karlto @ May 16 2006, 07:58 PM)
QUOTE(Dima202 @ May 17 2006, 03:10 PM)
Interesting, I was just sitting there trying to make zpsx to work. Then I rebooted the Zaurus when it came on neither the CF or SD started. I went to aterm typed in reboot. It is stuck on line "INIT: no more processes left in tis runlevel"  and that's it! It's just stuck there. I tried taking out battery, leaving zaurus dry for a few minutes. Turned on, same thing. Tested SD card in sd reader, reads it fine. CF card is a Symbol wifi card.
Anyone know what happened:(? Maybe there is a way to manually make it run? sad.gif  sad.gif  sad.gif

Thanks in advance! sad.gif

-My poor Z ohmy.gif

---Update: Also when it boots after I manually power off it says: "Inode #6581 was a directory with children - removing these too..." Children? Shoud I be worried? dry.gif
----Update: There is like 10 lines of these with different Inode numbers.
----Update: No the light on the Symbol card doesn't light up on boot, or when in startx.
----Update: Found that in /dev/ there is no mmcd????? This isn't right! right?
*

I can't even access the card. In /dev/ the mmcd is not there!
Can't access the CF either! sad.gif Maybe it corupted/deleted itself?sad.gif
Do you have a console? Try checking the filesystems on the cards - e.g. e2fsck if ext2 formatted.
*

Go to the top of the page
 
+Quote Post
karlto
post May 16 2006, 08:23 PM
Post #4





Group: Members
Posts: 343
Joined: 3-October 05
From: NZ
Member No.: 8,243



QUOTE(Dima202 @ May 17 2006, 05:06 PM)
QUOTE(karlto @ May 16 2006, 07:58 PM)

Do you have a console? Try checking the filesystems on the cards - e.g. e2fsck if ext2 formatted.

I can't even access the card. In /dev/ the mmcd is not there!
Can't access the CF either! sad.gif Maybe it corupted/deleted itself?sad.gif

I think these are all run by pcmcia - what is the output of 'dmesg'? Maybe the driver failed to load or one of the startup files is missing/corrupted so it isn't being loaded?
Go to the top of the page
 
+Quote Post
Dima202
post May 16 2006, 08:28 PM
Post #5





Group: Members
Posts: 68
Joined: 6-November 05
Member No.: 8,479



QUOTE(karlto @ May 16 2006, 08:23 PM)
QUOTE(Dima202 @ May 17 2006, 05:06 PM)
QUOTE(karlto @ May 16 2006, 07:58 PM)

Do you have a console? Try checking the filesystems on the cards - e.g. e2fsck if ext2 formatted.

I can't even access the card. In /dev/ the mmcd is not there!
Can't access the CF either! sad.gif Maybe it corupted/deleted itself?sad.gif

I think these are all run by pcmcia - what is the output of 'dmesg'? Maybe the driver failed to load or one of the startup files is missing/corrupted so it isn't being loaded?
*


Karlos, I decided to reinstall to beta 3.
Thanks for your help. But I just thought re-installing would be quicker, since I have most apps already on my sd cards which I want to install.

Thanks again for offering your help. I really appreciate it.
Go to the top of the page
 
+Quote Post

Reply to this topicStart new topic
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:

 



RSS Lo-Fi Version Time is now: 30th August 2014 - 06:32 PM