Bluetooth Na C1000 S Cacko 1.23 Options

[networ]

Vyzkousel jsem Bluetooth USB dongle MSI Btoes 2.0 fungoval na prvni pokus. Stacilo sparovat dongle s telefonem (pin je 1234) a pak nastavit PPP spojeni pres bluetooth. Zkousel jsem telefony Ericsson R520m a Siemens S75, oba fungovaly na prvni pokus bez problemu. U Siemense je problem, ze telefon zada pri kazdem novem ppp spojeni ze Zaura o pin kod. Zatim nevim, jak to obejit.

BT software pouzivam BlueZ z Cacko archivu.

Jeste jsem uspesne vyzkousel nejakou neznackovou GPS, ale jen po USB kabelu, ne po BT, na to se teprve chystam. Pouzil jsem GPS software qpeGPS.

ntw


dmesg po pripojeni MSI Btoes 2.0
---
hotplug_bh:
monitor_connected: 1
monitor_restore: RESTORE_LOADED
monitor_hotplug: agent: usbd interface: monitor action: restore-loaded
usbdcore: usbdcore 0.1 035 2002-06-12 20:00 (dbg="")
net_fd 0.1 035 2002-06-12 20:00 (dbg="",alwaysup=0,OUT=64,IN=64)
vendorID: 4dd productID: 9031
pxa27x_bi 0.1-alpha 035 2002-06-12 20:00 (dbg="")
bi_modinit: call udc_startup_events
bi_device_event: call udc_enable
bi_device_event: call udc_all_interrupts
udc_connect: usb-device is not active.

usbh: monitor_int_hndlr:
usbh: monitor_bh:

usbh: monitor_int_hndlr:
usbh: monitor_bh:

usbh: monitor_int_hndlr:
usbh: monitor_bh:
usbh: udc_connected: ACTIVE_LOW: 1<7>usbh: monitor_connected: 1
usbh: monitor_load: 4
usbh: monitor_hotplug: agent: usbh interface: monitor action: load
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-ohci.c: USB OHCI at membase 0xfe000000, IRQ 3
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usbh: udc_connected: ACTIVE_LOW: 1<7>usbh: monitor_connected: 1
usbh: monitor_load: 2
usbh: udc_connected: ACTIVE_LOW: 1<7>usbh: monitor_connected: 1
usbh: monitor_load: 2
hub.c: new USB device -2, assigned address 2
usb.c: USB device 2 (vend/prod 0xa5c/0x2101) is not claimed by any active driver.
BlueZ HCI USB driver ver 2.7 Copyright © 2000,2001 Qualcomm Inc
Written 2000,2001 by Maxim Krasnyansky <maxk@qualcomm.com>
usb.c: registered new driver hci_usb

[merli]

Vyzkousel jsem Bluetooth USB dongle MSI Btoes 2.0 fungoval na prvni pokus. Stacilo sparovat dongle s telefonem (pin je 1234) a pak nastavit PPP spojeni pres bluetooth. Zkousel jsem telefony Ericsson R520m a Siemens S75, oba fungovaly na prvni pokus bez problemu. U Siemense je problem, ze telefon zada pri kazdem novem ppp spojeni ze Zaura o pin kod. Zatim nevim, jak to obejit.

BT software pouzivam BlueZ z Cacko archivu.

Jeste jsem uspesne vyzkousel nejakou neznackovou GPS, ale jen po USB kabelu, ne po BT, na to se teprve chystam. Pouzil jsem GPS software qpeGPS.

ntw


dmesg po pripojeni MSI Btoes 2.0
---
hotplug_bh:
monitor_connected: 1
monitor_restore: RESTORE_LOADED
monitor_hotplug: agent: usbd interface: monitor action: restore-loaded
usbdcore: usbdcore 0.1 035 2002-06-12 20:00 (dbg="")
net_fd 0.1 035 2002-06-12 20:00 (dbg="",alwaysup=0,OUT=64,IN=64)
vendorID: 4dd productID: 9031
pxa27x_bi 0.1-alpha 035 2002-06-12 20:00 (dbg="")
bi_modinit: call udc_startup_events
bi_device_event: call udc_enable
bi_device_event: call udc_all_interrupts
udc_connect: usb-device is not active.

usbh: monitor_int_hndlr:
usbh: monitor_bh:

usbh: monitor_int_hndlr:
usbh: monitor_bh:

usbh: monitor_int_hndlr:
usbh: monitor_bh:
usbh: udc_connected: ACTIVE_LOW: 1<7>usbh: monitor_connected: 1
usbh: monitor_load: 4
usbh: monitor_hotplug: agent: usbh interface: monitor action: load
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-ohci.c: USB OHCI at membase 0xfe000000, IRQ 3
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usbh: udc_connected: ACTIVE_LOW: 1<7>usbh: monitor_connected: 1
usbh: monitor_load: 2
usbh: udc_connected: ACTIVE_LOW: 1<7>usbh: monitor_connected: 1
usbh: monitor_load: 2
hub.c: new USB device -2, assigned address 2
usb.c: USB device 2 (vend/prod 0xa5c/0x2101) is not claimed by any active driver.
BlueZ HCI USB driver ver 2.7 Copyright © 2000,2001 Qualcomm Inc
Written 2000,2001 by Maxim Krasnyansky <maxk@qualcomm.com>
usb.c: registered new driver hci_usb

Mal som podobny problem so SE T610 a Billionton CF card. Co nakoniec na Cacko 1.23 zaberalo iba vzdy vytriet PIN z mobilu a nadviazat trust vzdy pri dialovani.
Je to nejaky bug v Cacko pretoze po migracii na pdaxrom 1.1.0 beta 1 (chystam sa na beta 4 (2.6 kernel rules)) vsetko chodi ako ma.

Dobre vediet ze niekto v nasich oblastiach pouzive C1000! Kde si ju kupoval a kolko ta vysla?