Bogus Network Connection?, Zaurus Connects - but doesn't? Options

[Jacknife]

I'm able to connect to my WAP with 100% signal strength/quality, but am not able to see the Zaurus from my network nor the network from my Zaurus. I've never seen an issue like this before, and I'm kind of at a loss. I'm hoping that someone has seen this type of issue before and found a way to fix it.

Anyway, here's some network configuration dumps from both my Zaurus and Linux desktop:

Zaurus:

CODE

home/zaurus>/sbin/route;/sbin/route -n;/sbin/ifconfig
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
192.168.1.0     *               255.255.255.0   U     0      0        0 wlan0
default         192.168.1.1     0.0.0.0         UG    1      0        0 wlan0
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
192.168.1.0     0.0.0.0         255.255.255.0   U     0      0        0 wlan0
0.0.0.0         192.168.1.1     0.0.0.0         UG    1      0        0 wlan0
lo        Link encap:Local Loopback
         inet addr:127.0.0.1  Mask:255.0.0.0
         UP LOOPBACK RUNNING  MTU:16436  Metric:1
         RX packets:848 errors:0 dropped:0 overruns:0 frame:0
         TX packets:848 errors:0 dropped:0 overruns:0 carrier:0
         collisions:0 txqueuelen:0
         RX bytes:89821 (87.7 Kb)  TX bytes:89821 (87.7 Kb)

wlan0     Link encap:Ethernet  HWaddr 00:10:7A:58:C9:D9
         inet addr:192.168.1.104  Bcast:192.168.1.255  Mask:255.255.255.0
         UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
         RX packets:0 errors:0 dropped:0 overruns:0 frame:0
         TX packets:48 errors:0 dropped:0 overruns:0 carrier:0
         collisions:0 txqueuelen:100
         RX bytes:0 (0.0 b)  TX bytes:864 (864.0 b)
         Interrupt:135

Work station:

CODE

/home/jacknife>/sbin/route;/sbin/route -n;/sbin/ifconfig
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
192.168.1.0     *               255.255.255.0   U     0      0        0 eth0
169.254.0.0     *               255.255.0.0     U     0      0        0 eth0
127.0.0.0       *               255.0.0.0       U     0      0        0 lo
default         router          0.0.0.0         UG    0      0        0 eth0
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
192.168.1.0     0.0.0.0         255.255.255.0   U     0      0        0 eth0
169.254.0.0     0.0.0.0         255.255.0.0     U     0      0        0 eth0
127.0.0.0       0.0.0.0         255.0.0.0       U     0      0        0 lo
0.0.0.0         192.168.1.1     0.0.0.0         UG    0      0        0 eth0
eth0      Link encap:Ethernet  HWaddr 00:A0:C9:A5:DD:BB  
         inet addr:192.168.1.111  Bcast:192.168.1.255  Mask:255.255.255.0
         UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
         RX packets:463174 errors:0 dropped:0 overruns:0 frame:0
         TX packets:1935924 errors:0 dropped:0 overruns:0 carrier:0
         collisions:0 txqueuelen:100
         RX bytes:86686511 (82.6 Mb)  TX bytes:266125014 (253.7 Mb)
         Interrupt:9 Base address:0xccc0 Memory:f7000000-f7000038

lo        Link encap:Local Loopback  
         inet addr:127.0.0.1  Mask:255.0.0.0
         UP LOOPBACK RUNNING  MTU:16436  Metric:1
         RX packets:68549 errors:0 dropped:0 overruns:0 frame:0
         TX packets:68549 errors:0 dropped:0 overruns:0 carrier:0
         collisions:0 txqueuelen:0
         RX bytes:16182631 (15.4 Mb)  TX bytes:16182631 (15.4 Mb)

I know that at least my WAP can see the Zaurus connecting, because there is an entry in the logs with the connect time and MAC addresss. Despite this fact, I'm not able to ping the WAP from my Zaurus.

[Ragnorok]

- I'm having this same problem with a shiny new C1000 running the default Sharp ROM (1.1jp, i think, converted to engrish of course) with a DLink DCF-660W. It connectes, it works for about one web page load, maybe two, then it just stops. When that happens, it won't ping anything, not even the WAP. A netstat -a freezes after the third entry, and has to be CTRL-C to stop it or it'll sit there forever. Haven't done routing tables or anything yet.
- If I keep playing, the Z will ultimate "fade to white". Then *entire* screen slowly washes out until everything is full white. If the unit is suspended and the card pulled before it gets to full white, it will recover when turned back on, otherwise the reset button must be employed.
- I also have a somewhat flakey LinkSys WCF12 that behaves in precisely the same manner.
- Serious weirdness. I'll try the things Jacknife suggests and see what that does...