Bogus Network Connection?, Zaurus Connects - but doesn't? Options

[Jacknife]

I'm able to connect to my WAP with 100% signal strength/quality, but am not able to see the Zaurus from my network nor the network from my Zaurus. I've never seen an issue like this before, and I'm kind of at a loss. I'm hoping that someone has seen this type of issue before and found a way to fix it.

Anyway, here's some network configuration dumps from both my Zaurus and Linux desktop:

Zaurus:

CODE

home/zaurus>/sbin/route;/sbin/route -n;/sbin/ifconfig
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
192.168.1.0     *               255.255.255.0   U     0      0        0 wlan0
default         192.168.1.1     0.0.0.0         UG    1      0        0 wlan0
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
192.168.1.0     0.0.0.0         255.255.255.0   U     0      0        0 wlan0
0.0.0.0         192.168.1.1     0.0.0.0         UG    1      0        0 wlan0
lo        Link encap:Local Loopback
         inet addr:127.0.0.1  Mask:255.0.0.0
         UP LOOPBACK RUNNING  MTU:16436  Metric:1
         RX packets:848 errors:0 dropped:0 overruns:0 frame:0
         TX packets:848 errors:0 dropped:0 overruns:0 carrier:0
         collisions:0 txqueuelen:0
         RX bytes:89821 (87.7 Kb)  TX bytes:89821 (87.7 Kb)

wlan0     Link encap:Ethernet  HWaddr 00:10:7A:58:C9:D9
         inet addr:192.168.1.104  Bcast:192.168.1.255  Mask:255.255.255.0
         UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
         RX packets:0 errors:0 dropped:0 overruns:0 frame:0
         TX packets:48 errors:0 dropped:0 overruns:0 carrier:0
         collisions:0 txqueuelen:100
         RX bytes:0 (0.0 b)  TX bytes:864 (864.0 b)
         Interrupt:135

Work station:

CODE

/home/jacknife>/sbin/route;/sbin/route -n;/sbin/ifconfig
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
192.168.1.0     *               255.255.255.0   U     0      0        0 eth0
169.254.0.0     *               255.255.0.0     U     0      0        0 eth0
127.0.0.0       *               255.0.0.0       U     0      0        0 lo
default         router          0.0.0.0         UG    0      0        0 eth0
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
192.168.1.0     0.0.0.0         255.255.255.0   U     0      0        0 eth0
169.254.0.0     0.0.0.0         255.255.0.0     U     0      0        0 eth0
127.0.0.0       0.0.0.0         255.0.0.0       U     0      0        0 lo
0.0.0.0         192.168.1.1     0.0.0.0         UG    0      0        0 eth0
eth0      Link encap:Ethernet  HWaddr 00:A0:C9:A5:DD:BB  
         inet addr:192.168.1.111  Bcast:192.168.1.255  Mask:255.255.255.0
         UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
         RX packets:463174 errors:0 dropped:0 overruns:0 frame:0
         TX packets:1935924 errors:0 dropped:0 overruns:0 carrier:0
         collisions:0 txqueuelen:100
         RX bytes:86686511 (82.6 Mb)  TX bytes:266125014 (253.7 Mb)
         Interrupt:9 Base address:0xccc0 Memory:f7000000-f7000038

lo        Link encap:Local Loopback  
         inet addr:127.0.0.1  Mask:255.0.0.0
         UP LOOPBACK RUNNING  MTU:16436  Metric:1
         RX packets:68549 errors:0 dropped:0 overruns:0 frame:0
         TX packets:68549 errors:0 dropped:0 overruns:0 carrier:0
         collisions:0 txqueuelen:0
         RX bytes:16182631 (15.4 Mb)  TX bytes:16182631 (15.4 Mb)

I know that at least my WAP can see the Zaurus connecting, because there is an entry in the logs with the connect time and MAC addresss. Despite this fact, I'm not able to ping the WAP from my Zaurus.

[Ragnorok]

- The D-Link is just problematic. May be a bogus card ... it's not consistent in what's wrong each time, except that it often ends in a crash. (smirk) It is properly detected (usually) and has configuration in wlan.conf, but I haven't done a modprobe to see if prism_cs is loaded. It finally just refused to even be recognized as anything but a generic CF card, so I gave up on it.
- The LinkSys works perfectly, until it doesn't. (giggle) Route, netstat, cardctl, ifconfig, iwconfig, all give the same results before it doesn't work, and after. The only difference is that under Network, the SSID is garbulated (looks like a mix of random chars, with some boxes like Japanese chars appear), and the Quality is nothing. Signal is good, and loading the Network to see this crashes the Z.
- Comments? Suggestions? I'd like to have WiFi on this guy...