OESF | ELSI | pdaXrom | OpenZaurus | Zaurus Themes | Community Links | Ibiblio

IPB

Welcome Guest ( Log In | Register )

 
Reply to this topicStart new topic
> Unable To Jtag Swisscom
Berend
post Mar 21 2006, 10:04 AM
Post #1





Group: Members
Posts: 24
Joined: 2-October 05
From: The Netherlands
Member No.: 8,235



I finally did it, I bricked my Swisscom CL4. mad.gif

I re-flashed blupdater.img, to make sure it was that bootloader that I was using, and directly after that I uploaded the image Fred provided. Then I booted... Maybe that was stupid and I probably should have reset after uploading the bootloader. Anyway, the thing started booting, ran out of memory and halted. And now, aside from the recharching led and a brief flash of the backlight when it's turned on, it's dead.

I already had a JTAG cable and connectors soldered (~30cm, flatcable, 200Ohm resistors at JTAG connector), and I used both:
- The JTAG openwince-jtag deb package (0.5.1) and openwince-include deb
- Compiled JTAG 0.4 with the includes provided at openwince.sourceforge.net/includes

and tried:
jtag> cable ppdev /dev/{lp*,par*} DLC5
jtag> cable parallel 0x378 DLC5

Nothing, can't init the thing, tried it on an Ubuntu and Debian Sarge box. I suspect Sascha was right, perhaps the Swisscoms can't be JTAG'ed?

Just a warning sad.gif
Go to the top of the page
 
+Quote Post
Digi
post Mar 22 2006, 09:09 AM
Post #2





Group: Members
Posts: 13
Joined: 4-March 06
Member No.: 9,287



I jtagged 2 Swisscoms alright, no problem, used:

cable parallel 0x3bc DLC5
detect

Make sure which parallel port adress your host computer uses, in my case it is 0x3bc instead of the standard 0x378!

Digi


QUOTE(Berend @ Mar 21 2006, 07:04 PM)
I finally did it, I bricked my Swisscom CL4.  mad.gif

I re-flashed blupdater.img, to make sure it was that bootloader that I was using, and directly after that I uploaded the image Fred provided. Then I booted... Maybe that was stupid and I probably should have reset after uploading the bootloader. Anyway, the thing started booting, ran out of memory and halted. And now, aside from the recharching led and a brief flash of the backlight when it's turned on, it's dead.

I already had a JTAG cable and connectors soldered (~30cm, flatcable, 200Ohm resistors at JTAG connector), and I used both:
- The JTAG openwince-jtag deb package (0.5.1) and openwince-include deb
- Compiled JTAG 0.4 with the includes provided at openwince.sourceforge.net/includes

and tried:
jtag> cable ppdev /dev/{lp*,par*} DLC5
jtag> cable parallel 0x378 DLC5

Nothing, can't init the thing, tried it on an Ubuntu and Debian Sarge box. I suspect Sascha was right, perhaps the Swisscoms can't be JTAG'ed?

Just a warning sad.gif
*
Go to the top of the page
 
+Quote Post
Berend
post Mar 22 2006, 10:20 AM
Post #3





Group: Members
Posts: 24
Joined: 2-October 05
From: The Netherlands
Member No.: 8,235



Hey Digi,

dmesg told me it was 0x378, but alas.. You gave me some hope though, so I tried again. Fiddled a bit in the BIOS and yes, it works now! Wohoo

I'm not sure if the alternate BIOS settings add something, but I did have to start JTAG as superuser.I tried this yesterday, but it didn't seem to work then. BIOS is now set from ECP+EPP mode to 'normal', and I also changed the adress from 0x378 to 0x278.

thanx, I almost buried it!

CODE
jtag> cable parallel 0x278 DLC5
Initializing Xilinx DLC5 JTAG Parallel Cable III on parallel port at 0x278
jtag> detect
Device Id: 10001001001001100001000000010011
 Manufacturer: Intel
 Part:         SA1110
 Stepping:     B4
 Filename:     /usr/local/share/jtag/intel/sa1110/sa1110
Go to the top of the page
 
+Quote Post

Reply to this topicStart new topic
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:

 



RSS Lo-Fi Version Time is now: 31st October 2014 - 07:49 AM