OESF | ELSI | pdaXrom | OpenZaurus | Zaurus Themes | Community Links | Ibiblio

IPB

Welcome Guest ( Log In | Register )

> Refitting Cf Card For Sl-c3000, pics, English text, and comments
iamasmith
post May 31 2006, 10:26 AM
Post #1





Group: Members
Posts: 1,248
Joined: 6-July 04
Member No.: 3,928



This is a walkthrough of the process.

Do NOT try this unless all of the following criteria are met.

1. You don't care about the Warranty of either the device or the card.
2. You have a single screwdriver that will fit the screws of the Zaurus (they are all pretty much the same).
3. You have a soldering iron and skills necessary to use it.
4. You are really so driven to do it that you have to do it.

Do NOT complain to me, Sharp, your vendor or anyone if you break it badly.

Quite probable pitfalls..

1. You have chosen a card that has slightly higher power requirements than the Microdrive.. will cause failures immediately. Note, a working card in the CF slot does NOT mean a working card inside the Zaurus.
2. Your card may fail much quicker than the Microdrive - Trisoft had a card fail within 1 week of fitting it.
3. You may well strip the screws on the PCB of the Zaurus when removing it.. those robots at Sharp screw em in hard and you MUST have a screwdriver that fits exactly.
4. If you are particularly 'cack-handed' or have a screw driver that doesn't fit then the screw driver may slip and gouge a fairly important part of the unit.
5. You could crack the board.
6. You could zap components with static off your body.
7. You could seriously frustrate yourself tongue.gif

OK.. enough of the warnings, here is the nitty gritty.

Remove all obvious components from the base unit..

* CF Blank, Battery Cover, Battery, Stylus, SD Card Blank an Service Console Gromit from the back of the unit

Attached File  componentsout.jpg ( 93.57K ) Number of downloads: 394


Remove all the screws. Be particularly careful not to lose the screws at the base of the battery compartment inside the unit.

Note all screws are exactly the same so there is no need to ensure that you have them noted for replacement in the same holes.

With the utmost care remove the back housing.. it may seem to come free from the side nearest the SD slot first. Once it is free like this lift the side nearest the battery compartment (the other side is anchored by the earphone socket) and the back should come free without undue force.

Attached File  1stglipseinside.jpg ( 219.85K ) Number of downloads: 483


Take a close look at the main board. The two Marked A hold the board onto the mount. The two Marked B hold the CF housing onto the other side of the board. At some point you need to take them all out, if they will easily unscrew at this point then do it. If not I will suggest a tactic after removing this board.

Now note the area marked C, this varies from Zaurus to Zaurus. some may have a wire soldered here with enough slack to allow removal of the board. If as in this case there is a Copper Foil strip soldered to the unit then you must unsolder it before removing the board.

Attached File  offendingfoil.jpg ( 61.61K ) Number of downloads: 420


Note that each screw has a 'copper track' artwork arrow beside it on the PCB, you will use this to reference their replacement later.

Fold back the board which should now come out quite easily being extremely careful not to damage the ribbon cables attaching it to the screen and keyboard.

Attached File  mobofree.jpg ( 110.9K ) Number of downloads: 383


remove the two flat screws from the SD controller daughter board and remove the daughter board. If you need to apply pressure to the board to do this use something as a stanchion on the other side of the board. I simply placed the CF blanking plate under that area whilst doing this.

This should now lift off.

Attached File  sdcardslotoff.jpg ( 119.17K ) Number of downloads: 318


The next step is to remove the plastic housing for the CF card which has 2 clips and 2 hooks and if you didn't remove them earlier 2 screws (previously marked as cool.gif. If you had trouble eariler then I suggest that you get the SD Card blank, apply a little tape to it and adhere the tape to the Microdrive so that it holds the SD Card blank under the area where the screw is. You should be able to apply a little more force with the screwdriver now without fear of straining the board.

Attached File  cfhousingoff.jpg ( 129.67K ) Number of downloads: 293


Now simply replace the Microdrive with your chosen card...

Attached File  sandiskin.jpg ( 132.79K ) Number of downloads: 415


Now reassemble in reverse order, cross your fingers and do the software engineering bit (I class partitioning the device etc in that area).

-Andy
Go to the top of the page
 
+Quote Post
 
Start new topic
Replies
Snappy
post May 31 2006, 04:54 PM
Post #2





Group: Members
Posts: 793
Joined: 28-November 04
From: NM, US, sometimes Asia
Member No.: 5,633



wow! neat! smile.gif .... you gave me an idea. How about refitting a CF wifi card in that space? Possibly need to trim the CF card as most cards juts out a bit.
Go to the top of the page
 
+Quote Post
daniel3000
post Jun 1 2006, 12:11 AM
Post #3





Group: Members
Posts: 1,002
Joined: 28-April 05
From: Germany
Member No.: 7,027



QUOTE(Snappy @ Jun 1 2006, 02:54 AM)
wow! neat! smile.gif .... you gave me an idea. How about refitting a CF wifi card in that space? Possibly need to trim the CF card as most cards juts out a bit.
*


Indeed a very nice tutorial.
Thanks, Andy!

An I dea I had when reading albertr's instructions of fitting wifi and BT USB modules inside a C1000:

In a 3x00 you could replace the microdrive with a CF card which you removed the housing from first, so it will be much thinner.
This could allow to _additionally_ fit (i.e. stack) the USB modules in the same place as the CF card.

No idea if this would really work, but someone may want to try it.
(Well, don't try it with a dismantled Microdrive please, that certainly won't work ;-)

daniel
Go to the top of the page
 
+Quote Post
iamasmith
post Jun 1 2006, 12:26 AM
Post #4





Group: Members
Posts: 1,248
Joined: 6-July 04
Member No.: 3,928



QUOTE(daniel3000 @ Jun 1 2006, 08:11 AM)
...

An I dea I had when reading albertr's instructions of fitting wifi and BT USB modules inside a C1000:

In a 3x00 you could replace the microdrive with a CF card which you removed the housing from first, so it will be much thinner.
This could allow to _additionally_ fit (i.e. stack) the USB modules in the same place as the CF card.

No idea if this would really work, but someone may want to try it.
(Well, don't try it with a dismantled Microdrive please, that certainly won't work ;-)

daniel
*


Sorry if this sounds negative but NO, NO, NO, NO NO ! smile.gif

The housing around these storage cards almost certainly provides them with the RF shielding necessary for them to :-

a. Meet FCC/Euro or whatever compliance standards that there are with regard to emmissions.
b. Enable them to function in an environment with background electronic emmisions that are defined by these standards.
c. Meet the thermal characteristics that the manufacturer states in their documentation.

You may well experience glitches or complete meltdown if you try this. (any thoughts on this AlbertR if you are listening ?)

-Andy
Go to the top of the page
 
+Quote Post

Posts in this topic


Reply to this topicStart new topic
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:

 



RSS Lo-Fi Version Time is now: 23rd November 2014 - 01:52 AM