Usb Ethernet/wifi/thumbdrives With C3200, Some Questions.... Options

[ArchiMark]

OK, guys, go easy on ol' ArchiMark as I just got my new 3200 yesterday after selling my previous one a year ago....so no Z use for a long time....

Anyway, remembered that I had bought an iRiver PMP USB Host Adapter Cable before and would like to try using it with my Linksys USB200M v2.1 'ethernet stick' and also a USB thumbdrive and maybe a USB WiFi stick...

The thought is if I can do that, then I free up my CF card slot for additional storage and don't need to swap with ethernet or wifi cards, etc....

As I just got Z yesterday, still have Sharp ROM on it, but figure that will change soon....pdaXii probably or Debian????

Anyway, what should I do to get this working???

Thanks for any and all suggestions!

Mark

[Jon_J]

I don't know if this will help.
I know somewhere on these forums, probably in more than one place, there is mention of the 2.6 kernel setups playing a stricter role of monitoring USB power at the USB port. This was mentioned quite some time ago in Open Zaurus, and some people were having trouble with USB dongles that just worked in the older 2.4 kernel.
I just hooked up my Belkin - F5D5050 USB 1.1 10/100 Ethernet Adapter to my router and my C3200.
In pdaxii13, I need to open the "Lan and WiFi" app and make the connection.
I'm online with it now.
Below is dmesg output from the first usb entry.
Note: Look at the last 3 or 4 lines. This is where my dongle actually shows as being used.

CODE

usbh: monitor_int_hndlr:
usbh: monitor_bh:
usbh: udc_connected: ACTIVE_LOW: 1<7>usbh: monitor_connected: 1
usbh: monitor_load: 4
usbh: monitor_hotplug: agent: usbh interface: monitor action: load
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-ohci.c: USB OHCI at membase 0xfe000000, IRQ 3
usb.c: new USB bus registered, assigned bus number 1
usb.c: kmalloc IF c203cec0, numif 1
usb.c: new device strings: Mfr=0, Product=2, SerialNumber=1
usb.c: USB device number 1 default language ID 0x0
Product: USB OHCI Root Hub
SerialNumber: fe000000
hub.c: USB hub found
hub.c: 2 ports detected
hub.c: standalone hub
hub.c: ganged power switching
hub.c: individual port over-current protection
hub.c: Port indicators are not supported
hub.c: power on to power good time: 8ms
hub.c: hub controller current requirement: 0mA
hub.c: port removable status: RR
hub.c: local power source is good
hub.c: no over-current condition exists
hub.c: enabling power on all ports
usb.c: hub driver claimed interface c203cec0
usb.c: kusbd: /sbin/hotplug add 1
hub.c: port 1, portstatus 100, change 0, 12 Mb/s
hub.c: port 2, portstatus 101, change 1, 12 Mb/s
hub.c: port 2 connection change
hub.c: port 2, portstatus 101, change 1, 12 Mb/s
hub.c: port 2, portstatus 101, change 0, 12 Mb/s
hub.c: port 2, portstatus 101, change 0, 12 Mb/s
hub.c: port 2, portstatus 101, change 0, 12 Mb/s
hub.c: port 2, portstatus 101, change 0, 12 Mb/s
hub.c: port 2, portstatus 103, change 10, 12 Mb/s
hub.c: new USB device -2, assigned address 2
usb.c: kmalloc IF c203c860, numif 1
usb.c: new device strings: Mfr=1, Product=2, SerialNumber=3
usb.c: USB device number 2 default language ID 0x409
Manufacturer: ADMtek
Product: USB To LAN Converter
SerialNumber: 0001
usb.c: unhandled interfaces on device
usb.c: USB device 2 (vend/prod 0x50d/0x121) is not claimed by any active driver.
  Length              = 18
  DescriptorType      = 01
  USB version         = 1.10
  Vendor:Product      = 050d:0121
  MaxPacketSize0      = 8
  NumConfigurations   = 1
  Device version      = 1.01
  Device Class:SubClass:Protocol = 00:00:00
    Per-interface classes
Configuration:
  bLength             =    9
  bDescriptorType     =   02
  wTotalLength        = 0027
  bNumInterfaces      =   01
  bConfigurationValue =   01
  iConfiguration      =   00
  bmAttributes        =   a0
  MaxPower            =  160mA

  Interface: 0
  Alternate Setting:  0
    bLength             =    9
    bDescriptorType     =   04
    bInterfaceNumber    =   00
    bAlternateSetting   =   00
    bNumEndpoints       =   03
    bInterface Class:SubClass:Protocol =   00:00:00
    iInterface          =   00
    Endpoint:
      bLength             =    7
      bDescriptorType     =   05
      bEndpointAddress    =   81 (in)
      bmAttributes        =   02 (Bulk)
      wMaxPacketSize      = 0040
      bInterval           =   00
    Endpoint:
      bLength             =    7
      bDescriptorType     =   05
      bEndpointAddress    =   02 (out)
      bmAttributes        =   02 (Bulk)
      wMaxPacketSize      = 0040
      bInterval           =   00
    Endpoint:
      bLength             =    7
      bDescriptorType     =   05
      bEndpointAddress    =   83 (in)
      bmAttributes        =   03 (Interrupt)
      wMaxPacketSize      = 0008
      bInterval           =   80
usb.c: kusbd: /sbin/hotplug add 2
pegasus.c: v0.4.32 (2003/06/06):Pegasus/Pegasus II USB Ethernet driver
usb.c: registered new driver pegasus
pegasus.c: eth0: Belkin F5D5050 USB Ethernet
pegasus.c: setup Pegasus II specific registers
usb.c: pegasus driver claimed interface c203c860
root-:)