Simpad Slc Out Of Order? Options

[Silvester]

Hi,
yesterday i bought a used simpad slc and spend nearly all free time with it. Unfortunately it´s out of order from the beginning.

After connecting the power supply, there are coloured lines all over the display and after some seconds one can see a bluescreen and nothing else happens, no sound or anything else...

I am not shure what this means. Is the mainboard death? Is it a bootloader or anything else problem, that can be fixed by spending time on it?

Please help me out...

Thx in advance, Silvester

[Silvester]

ok, I tried again. First coloured lines, after a few seconds bluescreen. After 15 Minutes I pushed the battery switch. same effect, first lines, then blue screen. nothing else. :-(

But if its normal for the simpad to boot this way, it´s perhaps a problem while booting. How can I find out? Should I try to solder a serial Adapter? If so, which one? The one with the lundberg Adaptor or direct connection between parport and Simpad?

Greetings Silvester

[mister_data]

ok, I tried again. First coloured lines, after a few seconds bluescreen. After 15 Minutes I pushed the battery switch. same effect, first lines, then blue screen. nothing else. :-(

But if its normal for the simpad to boot this way, it´s perhaps a problem while booting. How can I find out? Should I try to solder a serial Adapter? If so, which one? The one with the lundberg Adaptor or direct connection between parport and Simpad?

Greetings Silvester

Hi Silvester,

you need a serial cable -> http://www.oesf.org/forum/index.php?s=&...st&p=174015.

If your pc run windows (98SE, 2k, XP...), try hyperterminal 38400 baud 8N1 and look
for messages from siemens bootloader.

If bootloader is okay and only your hpc2000/wince image is broken then reflash should help.
But for this you need the serial cable first.

Regards,
mrdata

[Silvester]

ok, I tried again. First coloured lines, after a few seconds bluescreen. After 15 Minutes I pushed the battery switch. same effect, first lines, then blue screen. nothing else. :-(

But if its normal for the simpad to boot this way, it´s perhaps a problem while booting. How can I find out? Should I try to solder a serial Adapter? If so, which one? The one with the lundberg Adaptor or direct connection between parport and Simpad?

Greetings Silvester

Hi Silvester,

you need a serial cable -> http://www.oesf.org/forum/index.php?s=&...st&p=174015.

If your pc run windows (98SE, 2k, XP...), try hyperterminal 38400 baud 8N1 and look
for messages from siemens bootloader.

If bootloader is okay and only your hpc2000/wince image is broken then reflash should help.
But for this you need the serial cable first.

Regards,
mrdata

Finally the Siemens Data cable arrived... resolderd it, trying to avoid hurting myself too much and:

Booting...
================================================
Siemens Switzerland Bootloader V2.4 20.07.2001
Running @206Mhz Processor ID 0x6901b119
Press ESC for monitor
Occupied Memory: [0x00004000-0x00008000],[0x00008014-0x0007cb9c]
Flash Id 0x00000018 at virt adr 0x05000000 Size 0x01000000
No 32Bit Flash detected 0x00000000
FlashImage Checksum 0x05040014-0x05061ab0=0xcd105fd8 Bootloader Image OK
Fabdata Flash @0x05061ab4 Ram @0x00029ab4 FABDATA: S843-KKUNN
MSC2=0x211954e0 :: MQ200 - Revision ID=2 ...
Initialise PCMCIA Interface... done.
Codec UCB1200 ID:0x1005 Ver.5 Dev.0 Suppl.1 IO 0x00000000
Erasing memory after power loss

ERASE SDRAM FROM 0x80000 to 0x1f00000
No PCMCIA Card Attached
No serial download request
Boothdr at 0x05080000 -> 0x31415926
Loading executable with header 0x0000
[*********************/] 0kB/sec
Done

whatever this means. I am pretty sure it´s a good sign!

I ve tried the thing with the escape button, but no more things.

Hope you can help me out another time...

[Silvester]

I followed this instructions:

http://www.silentservices.de/simpad/simpad-install-howto.txt

and this is the result:

Siemens Switzerland Bootloader V2.5.3 10.06.2003
Running @206Mhz Processor ID 0x6901b119
Press ESC for monitor
Occupied Memory: [0x00004000-0x00008000],[0x00008014-0x0007500c]
Flash Id 0x00000018 at virt adr 0x05000000 Size 0x01000000
No 32Bit Flash detected 0x00000000
FlashImage Checksum 0x05040014-0x05059f11=0x8912ac03 Bootloader Image OK
Fabdata Flash @0x05059f18 Ram @0x00021f18 FABDATA: S843-KKUNN
MQ200 - Revision ID=2 ...
Initialise PCMCIA Interface... done.
Codec UCB1200 ID:0x1005 Ver.5 Dev.0 Suppl.1 IO 0x00000000
Erasing memory after power loss

ERASE SDRAM FROM 0x80000 to 0x1f00000
No PCMCIA Card Attached
NO PCMCIA CARD! -- Use serial IO
Sysinit done
No serial download request
Boothdr at 0x05080000 -> 0x31415926
Loading executable with header 0x0000
[*********************|] 0kB/sec
Done

I then tired to install the german ce4.0 image, following this instructions again:

http://www.silentservices.de/simpad/simpad-install-howto.txt

everything seems fine until the last reset. I get coloured lines and after a few seconds a blue screen.

Any ideas? Perhaps the bootloader is damaged?

xxx

Silvester

[Silvester]

update:

I´ve tried this image: S843-SI-GER-104 SLC, Image Rel. 104 languague: German, CE .net 4.0

with

serload

from this page:

http://opensimpad.org/index.php/Windows#SLC

first time it said that there are more than 5 Mio long words different,

second time i tried there where still about 200.000 longwords different.

I renamed the image just for easier handling. Is this perhaps a problem?

Greetings

Silvester

[tml]

Doesn't serload provide some kind of monitor?

I think there is a chance that the people who could definitely answer your question no longer read this forum but have moved to the zaurus community.