![]() |
![]() ![]() |
![]() |
![]()
Post
#1
|
|
Group: Members Posts: 10 Joined: 3-December 07 Member No.: 21,022 ![]() |
I nedd help to put my zaurus SL-3100 to work on this CF Wireless "Agere".
h//p://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=350076134008 Any one can help me???? Regards Paulo |
|
|
![]()
Post
#2
|
|
![]() Group: Admin Posts: 3,492 Joined: 29-July 04 From: Cambridge, England Member No.: 4,149 ![]() |
if you put it in your zaurus and tell us the output of "cardctl ident", "cardctl status", "cardctl config" we might be able to tell you something useful about it.
if you're lucky there will be a driver for it. if you're running debian or angstrom you might need "pccardctl" as the command. |
|
|
![]()
Post
#3
|
|
Group: Members Posts: 10 Joined: 3-December 07 Member No.: 21,022 ![]() |
I like to config for Pdaxrom
"cardctl ident" Product "agere system madfid: 0x0156,0x0003 funcion: 4 (fixed disk) "cardctl status" 3.3v 16bits PC Card Funcion 0: Ready "cardctl config" VCC 3.3V Vpp1 3.3V Vpp2 3.3V I Try to install drives in h//p://www.tyrannozaurus.com/feed/beta3/custom/ hermes-wifi_7.18_armv5tel.ipk but no sucesse Can you help?? Regards Paulo |
|
|
![]()
Post
#4
|
|
![]() Group: Admin Posts: 3,492 Joined: 29-July 04 From: Cambridge, England Member No.: 4,149 ![]() |
looks like it's a Prism2 card, so you should use the hostap driver, that will give you WPA using wpa_supplicant, you might need to install the latter program.
don't use wlan-ng driver (aka hermes or orinoco) as you'll only get WEP to work. |
|
|
![]()
Post
#5
|
|
Group: Members Posts: 10 Joined: 3-December 07 Member No.: 21,022 ![]() |
Were I can find the drives and how do I install on pdaxrom?
I am not a Linux expert, but I am trying to my best. Regard's Paulo |
|
|
![]()
Post
#6
|
|
![]() Group: Members Posts: 2,342 Joined: 30-July 06 Member No.: 10,575 ![]() |
HostAP drivers should be installed by default. Try doing a "modprobe hostap" and/or a "modprobe hostap_cs" (either of which should load the HostAP modules), then the normal ifconfig/iwconfig/dhcpcd commands.
I can give a full command list, if necessary. HTH |
|
|
![]()
Post
#7
|
|
Group: Members Posts: 10 Joined: 3-December 07 Member No.: 21,022 ![]() |
I install the drives hermes-wifi_7.18_armv5tel.ipk but is the same, thosent work.
I make "iwconfig", and appears eth0, and say "warnig: Drives for device eth0 has been complied with version 1.4. the recommend version 1.5. In command "ifconfig eth0 up" it is not any eth0 and appears "S10CSIFFLAGS: no such device". I try to make "modprobe hostap" and say "Can's Load module Hostap |
|
|
![]()
Post
#8
|
|
Group: Members Posts: 8 Joined: 29-August 08 Member No.: 22,283 ![]() |
Hi i have the same model of card and im trying to get it running with a sl-c1000
iwconfig shows it as: wlan0 IEEE 802.11b Channel:0 Tx-Power=off Sensitivity:1/3 RTS thr:off Power Management:off Link Quality:0 Signal level:0 Noise Level:0 RX invalid nwid:0 Rx invalid crypt:0 Rx nvalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 trying to bring up the device with ifconfig gives #ifconfig wlan0 up SIOCSIFFLAGS: No such device Im running cacko 1.23 and im not sure of the next move |
|
|
![]() ![]() |
![]() |
Lo-Fi Version | Time is now: 20th April 2018 - 08:53 AM |