OESF | ELSI | pdaXrom | OpenZaurus | Zaurus Themes | Community Links | Ibiblio

IPB

Welcome Guest ( Log In | Register )

> Post Install Tweeks, That would make life easyer
craigtyson
post Jun 4 2009, 09:43 AM
Post #1





Group: Members
Posts: 464
Joined: 15-June 04
Member No.: 3,698



Having installed ZUBUNTU for the first time, here are some bits that people might find of use

after loging in the first time run

ts_calibrate

to calibrate your touch screen

run killall tskeys

to get some free memory

ensure dhcp is running properly by changing the 102 and 103 entries for dhcp in /etc/passwd to 0

get your wifi / network running by looking on the forums

once you have internet connectivity, install synaptic so you can find packages with

apt-get install synaptic

now you're ready to rock

Go to the top of the page
 
+Quote Post
 
Start new topic
Replies
ptoki
post Jul 9 2009, 09:58 AM
Post #2





Group: Members
Posts: 90
Joined: 1-April 08
From: Silesia
Member No.: 21,583



at my c1000 its not nessesary to kill tskeys
its sufficient to edit /etc/zaurusd/mach-config-vars and put TSKEYS_DEVICE=/dev/input/event2 instead default value

another must do thing is:
alsamixer:
set headphone, pcm, speaker to the top
unmute all left mixers (four of them) and right mixer (leave other right mixers muted)
finally enable speaker function (third control from end)

This gives clear sound through speaker and working headphones in stereo.

bass, treble, 3d set as you like. Play a bit with all of this deemphasis and filter thing if you have audiohile ear.

if your usb device does not work try dmesg and look if there is something like this:
usb 1-2: new full speed USB device using pxa27x-ohci and address 6
usb 1-2: rejected 1 configuration due to insufficient available bus power
usb 1-2: no configuration chosen from 1 choice

if you encounter problems with usb power then here is solution: http://www.oesf.org/forum/index.php?showto...mp;hl=usb+power

tweak a bit zaurus leds:
echo mmc0 > /sys/class/leds/spitz\:green\:mail/trigger
echo ide-disk > /sys/class/leds/spitz\:amber\:charge/trigger

if you like put it in /etc/init.d/zaurusd right after echo "starting zaurusd"
this gives you blinking leds while accessing cards.

Make some swap, 64MB is quite enough for pda use, if you intend to use zaurus with zubuntu as a little laptop it may be neccessary to put some more swap.

install lynx, dillo, mpg321 (uses a lot less cpu), fbreader, consider installing mpd

after that zubuntu is very fine. I would even say it may be a new cacko.

Great job for its creators and maintainers! I dont miss cacko smile.gif

In case you encounter "Unresolved Inheritance Operation" do as http://www.oesf.org/forum/index.php?showtopic=26703 thread says.
xfig, xpat2, xmpuzles are affected.
Go to the top of the page
 
+Quote Post
danboid
post Apr 22 2010, 02:28 PM
Post #3





Group: Members
Posts: 682
Joined: 26-December 05
From: Rochdale, Lancashire
Member No.: 8,789



QUOTE(ptoki @ Jul 9 2009, 06:58 PM) *
tweak a bit zaurus leds:
echo mmc0 > /sys/class/leds/spitz\:green\:mail/trigger
echo ide-disk > /sys/class/leds/spitz\:amber\:charge/trigger

if you like put it in /etc/init.d/zaurusd right after echo "starting zaurusd"
this gives you blinking leds while accessing cards.


This would seem to be wrong or at least outdated. If I add

CODE
echo "mmc0" > /sys/class/leds/spitz\:green\:hddacti/trigger


to zaurusd then the green led blinks whilst zubuntu boots then after its booted (ie after running the zaurusd daemon) the green LED only blinks when I access the SD card.

As far as I can tell you can only have one event / device (in this case mmc0 or ide-disk) assigned per LED trigger although under 2.4 based distros my green LED would flash when I accessed either the CF or SD interfaces.

Have I misunderstood or is there a workaround for this?
Go to the top of the page
 
+Quote Post
ptoki
post Apr 25 2010, 11:15 AM
Post #4





Group: Members
Posts: 90
Joined: 1-April 08
From: Silesia
Member No.: 21,583



QUOTE(danboid @ Apr 23 2010, 12:28 AM) *
QUOTE(ptoki @ Jul 9 2009, 06:58 PM) *
tweak a bit zaurus leds:
echo mmc0 > /sys/class/leds/spitz\:green\:mail/trigger
echo ide-disk > /sys/class/leds/spitz\:amber\:charge/trigger

if you like put it in /etc/init.d/zaurusd right after echo "starting zaurusd"
this gives you blinking leds while accessing cards.


This would seem to be wrong or at least outdated. If I add

CODE
echo "mmc0" > /sys/class/leds/spitz\:green\:hddacti/trigger


to zaurusd then the green led blinks whilst zubuntu boots then after its booted (ie after running the zaurusd daemon) the green LED only blinks when I access the SD card.

As far as I can tell you can only have one event / device (in this case mmc0 or ide-disk) assigned per LED trigger although under 2.4 based distros my green LED would flash when I accessed either the CF or SD interfaces.

Have I misunderstood or is there a workaround for this?


Well, I have only c1000 device so I cant tell how other devices behave. I confirm that there is possible to have only one device triggering LED. At least I did not try to echo something else than one trigger name.
Your code is correct and works as should to.
In c1000 there are two leds. And in my case I have two leds for cf and sd card blinking separately.

Additionally I can tell that amber led (charge) is acting problematically. Sometimes it works and sometimes it does not blink even when I am reading files on cf card.
Go to the top of the page
 
+Quote Post

Posts in this topic
craigtyson   Post Install Tweeks   Jun 4 2009, 09:43 AM
RX Shorty   Nice Thanks, I am going to try Zubuntu tonight.   Jun 19 2009, 05:45 PM
ptoki   at my c1000 its not nessesary to kill tskeys its s...   Jul 9 2009, 09:58 AM
RGRICH   QUOTE(ptoki @ Jul 9 2009, 02:58 PM) at my...   Dec 5 2009, 11:35 AM
ptoki   QUOTE(RGRICH @ Dec 5 2009, 09:35 PM) QUOT...   Dec 22 2009, 02:08 AM
danboid   QUOTE(ptoki @ Jul 9 2009, 06:58 PM) tweak...   Apr 22 2010, 02:28 PM
ptoki   QUOTE(danboid @ Apr 23 2010, 12:28 AM) QU...   Apr 25 2010, 11:15 AM
danboid   QUOTE(ptoki @ Apr 25 2010, 08:15 PM) QUOT...   Apr 26 2010, 12:22 AM
ptoki   QUOTE(danboid @ Apr 26 2010, 10:22 AM) QU...   Apr 26 2010, 02:30 AM
brontoZaurus   QUOTE(craigtyson @ Jun 4 2009, 07:43 PM) ...   Jul 23 2009, 03:35 AM
craigtyson   QUOTE(brontoZaurus @ Jul 23 2009, 11:35 A...   Jul 24 2009, 06:44 AM
brontoZaurus   oh! yes from shell it works, but from the menu...   Jul 26 2009, 11:49 PM
craigtyson   QUOTE(brontoZaurus @ Jul 27 2009, 07:49 A...   Jul 27 2009, 02:47 AM
brontoZaurus   ok but where is located that fileż? thanks in adva...   Jul 27 2009, 04:02 AM
ptoki   Another chunk of post install tweaks. Put CODE#m...   Jul 30 2009, 08:00 AM
ptoki   To make irda work: Ensure that modules irda, ircom...   Aug 5 2009, 09:30 PM
ptoki   Another batch of tweaks: Do not use LXDE, it has ...   Sep 11 2009, 12:18 AM
craigtyson   QUOTE(ptoki @ Sep 11 2009, 08:18 AM) Anot...   Sep 11 2009, 01:56 AM
ptoki   Next thing to do is to make dual boot with cacko. ...   Feb 15 2010, 02:43 AM
danboid   Hi ptoki! I'm not quite sure what you mea...   Apr 29 2010, 07:58 AM
ptoki   Here is my script: CODE#!/bin/sh ONE=$(gr...   May 1 2010, 01:14 AM


Reply to this topicStart new topic
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:

 



RSS Lo-Fi Version Time is now: 28th December 2014 - 12:10 PM