C1000 - Hw Pb With Touch Screen, In DEBUG MODE : bad position // the stlet's action. Options

[randy11]

Hello,
I've some troublshooting with my C1000. When I use the point to press in the screen, the action isn't recognized.

In "DEBUG MODE", there is 3 pages and in the page 3, the choice 7, there is "7. Extra Menu".
In "Extra menu" -> "1 Zaurus Test" -> "7. H Display". This option presents the character "H" or "h" on all the screen. When a place is touched, the screen commute between "H" and "h". This test is OK.

But, under Cacko, PdaXrom, the action isn't recognized. Isn't possible to make a new sceen's setup, where you press in the 4 coins of the screen.

Could you help me, to solve my problem ? A zaurus without touchscreen is too sad

Thanks a lot.

Randy

[Jon_J]

Hello,
I've some troublshooting with my C1000. When I use the point to press in the screen, the action isn't recognized.

In "DEBUG MODE", there is 3 pages and in the page 3, the choice 7, there is "7. Extra Menu".
In "Extra menu" -> "1 Zaurus Test" -> "7. H Display". This option presents the character "H" or "h" on all the screen. When a place is touched, the screen commute between "H" and "h". This test is OK.

But, under Cacko, PdaXrom, the action isn't recognized. Isn't possible to make a new sceen's setup, where you press in the 4 coins of the screen.

Could you help me, to solve my problem ? A zaurus without touchscreen is too sad

Thanks a lot.

Randy

If you have Cacko loaded try to recalibrate the screen.
Navigate using the keyboard to the "Settings" screen. (Use the "Home" key to switch tabs to "Settings").
Next, using the arrow pad, navigate to "Recalibrate". It is self explanatory, as I just did it on my C3100.

[randy11]

Hi Jon_J,

I've tried to install a Cacko, but you must "Tap" on the screen => No results.
I've also try with a PdaXrom, same result

If you have Cacko loaded try to recalibrate the screen.
Navigate using the keyboard to the "Settings" screen. (Use the "Home" key to switch tabs to "Settings").
Next, using the arrow pad, navigate to "Recalibrate". It is self explanatory, as I just did it on my C3100.

Thanks for your reply

[InSearchOf]

Hi Jon_J,

I've tried to install a Cacko, but you must "Tap" on the screen => No results.
I've also try with a PdaXrom, same result

If you have Cacko loaded try to recalibrate the screen.
Navigate using the keyboard to the "Settings" screen. (Use the "Home" key to switch tabs to "Settings").
Next, using the arrow pad, navigate to "Recalibrate". It is self explanatory, as I just did it on my C3100.

Thanks for your reply

From the command line, remove /etc/pointercal and run startx again.
or ts_calibrate should do the trick.

Late

[randy11]

From the command line, remove /etc/pointercal and run startx again.
or ts_calibrate should do the trick.

Late

Hi InSearchOf,

Under PdaXRom, I've allready remove /etc/pointercal and run startx again : the display stay "off-line".

The screen is rougly working in DEBUG-MODE but not with an OS ...?

Thanks.

[ptoki]

From the command line, remove /etc/pointercal and run startx again.
or ts_calibrate should do the trick.

Late

Hi InSearchOf,

Under PdaXRom, I've allready remove /etc/pointercal and run startx again : the display stay "off-line".

The screen is rougly working in DEBUG-MODE but not with an OS ...?

Thanks.

The question is whether this test is showing good behavior of your TS.

Check if there is no sand/screen protector between screen and its bezel.
If something is there then it is constantly pressing touch screen and acting strangely.
Try to peek straight device for any data going from there when you touching TS. This will give you any idea if communication is working.