Cacko Kernel For Sl-5500/5000d
Cacko Kernel For Sl-5500/5000d
Apr 14 2004, 04:49 AM
Joined: 22-October 03
Member No.: 89
Cacko Kernel is an updated kernel image for Sharp ROM 3.10/3.13 and compatible ROMs.
This NOT a full ROM update, this is only a kernel. You'll be able to continue to use your existing ROM after you flash this kernel update.
zImage-sl5500-32-30 - default memory layout
zImage-sl5500-64-0 - memory layout for home on SD ROM (Cacko/Crow)
zImage-sl5000D-32-0 - memory layout for home on SD ROM (Cacko/Crow)
Important information regarding 64-0 and 32-0 kernels!
Such kernels are only intended to be used on top of existing 64-0( or 32-0) Cacko/Crow ROM!!! I will not work if you flash it on top of 32-30 (default) ROM.
Also, it's not garantied to be compatible with TKC home on SD ROM, since it uses a different approach to implement it. However a 32-30 kernel may work.
If you want to use 64-0 (32-0) configuration. you must flash one of the Cacko/Crow ROMs first, depending on your zaurus model (5500 or 5000D):
Read more info on Cacko/Crow ROM here:
Also note, that if you perform a ROM update (not just kernel), I cannot garantee that you backups can be safely restored. They may or may not work, depending on what changes were made to your ROM. You can try and see if they do.
You сan safely use backups if you only flashed the kernel.
The kernel includes several improvments over the stock ROM.
- APM patch from OpenZaurus kernel (adopted for 2.4.18 kernel version by Albert Rybalkin).
This patch implements accurate batery power reading, which allows to display actual percentage
of remaining battery power instead of Good, Low, etc levels.
- Compiled with CONFIG_FS_SYNC flag turned off. The CONFIG_FS_SYNC flag is a modification added by Sharp
to force media (i.e., CF & SD cards) to be mounted sync, even if you specify "mount -o async ...".
With this flag turned off, you can get true async io on your SD and CF cards, greatly speeding up file writes
- Wireless Extentions enabled, orinoco/sectrum drivers updated to version 0.13e with monitoring patch applied.
This should enable Wellenreiter to run properly.
- Kernel is compiled with smaller console fonts, so that more information fits into the display.
- Applied patch, which fixes problem with serial CF cards staying suspended upon resume
- Included patch for IRDA problem with some Ericson mobile phones.
Issue the following commands after reboot to adjust IRDA settings for ericsson phones:
echo 1 > /proc/sys/net/irda/max_tx_window
echo 1000 > /proc/sys/net/irda/min_tx_turn_time
- Boot logo updated
Kernel Update instructions:
1. Make a backup of your data using Backup/Restore application.
Note: Although this update only replaces your Zaurus Linux kernel and does not change any other files,
you'll need to perform a hard reset after flashing to activate it the new kernel,
2. Download and copy zImage file to your CF card and perform a usual update procedure.
Make sure to press reset button after update is complete.
Note: Kernel is a small file so update will only take a few seconds.
3. Boot your Zaurus and restore your data from the backup.
To be able to restore your backup, rename your backup file, so that it ends with "unknown". For example:
After that the Backup/Restore app should recognize this backup.
4. To get actual battery percentage displayed in Qtopia, you need an updated version of Battery Applet,
which is available for download: http://my-zaurus.nadrod.ru/opie.html
Apr 15 2004, 11:00 AM
Joined: 14-April 04
From: Langley, BC Canada
Member No.: 2,847
I have attempted to update using the above kernel but when I reset all I get is the boot logo and it sits there. I am assuming that when you state "using the usual updat procedure" you are referring to the RESET and C+D option.
Please, make all the usual "CF card flashing" checks, such as your card is FAT16, zImage is the only file on the root of CF, it's named exactly zImage, etc.
What boot logo do you see? If ts's Sharp logo, kernel did not flash...
Try to flash zaurus with Ospack from Sharp and see if it works.
same happening here - boots with penguin, but then sits there. This is the 64-0 kernel. Is it unpacking the /home/ tar file? How long should I expect this to take?
My MMC card was already formatted to ext2, so I assume I don't need to fdisk and reformat...?
It's sitting there, having printed:
INIT: version 2.78 booting
This is exactly the situation I have using the 64-0 kernel, but now I have tried the 32-30 default kernel and it works fine.
Another thing, the link posted to the new battery applet is dead. Is there another location for this applet. The ZSI site has a protest page up so I can't get it from there either.
|Lo-Fi Version||Time is now: 26th February 2017 - 06:34 AM|