OESF | ELSI | pdaXrom | OpenZaurus | Zaurus Themes | Community Links | Ibiblio


Welcome Guest ( Log In | Register )

> UPDATED: SOLUTION: HOW TO setup 4GB (Muvo) Microdrive
post Apr 30 2004, 05:34 PM
Post #1

Group: Members
Posts: 608
Joined: 14-April 04
Member No.: 2,853

I need some help getiing my 4GB drive recognized by BOTH Windows XP and Linux.

I would prefer 1 partition, but two would be be fine if required.

Could someone tell me step-by-step how to partition and format my 4GB Microdrive card to handle the above conditions. I am a newbie so please be as specific as possible. I can get into the terminal program, but from there I would need the exact commands to get the drive partitioned and formated.

Thanks, in Advance.

BTW, I am using a C860 with Cacko Qtopia

UPDATED - Here's the answer
(I copied my solution to this original post, so you need not read further than this post, but an alternate Win 98 solution is provided in subsequent posts below.)

After some research, I got it all working in 17 simple steps. smile.gif (MODERATOR: This is a good candidate for FAQ inclusion).

Here is it, step by step FROM TELNET KONSOLE

NOTE: If you mess up any of these commands, you may find that backspace and arrows keys do not work and just insert escape sequences... don't panic, just hit CTRL-C to abort the command, which will bring you back to the command prompt. then just pick up where you left off.


0) su - root <enter> then enter password or enter if none.

1) #fdisk /dev/hda

2) Press m <ENTER> help

3) Press d <enter> deletes a partition

4) Select 1 <enter> Repeat delete of all partitions

5) Press w <enter> write (which also exits)

6) #fdisk /dev/hda (again ;-) )

7) Press n<enter> New Partition (Not listed in "m" help, but it will work).

8 ) Press p <enter> Primary Partition

8a) Press 1 <enter> for partition 1.

9) Press 2 <enter> ALWAYS start at cylinder 2 (don't ask, just do it).

10) Press <enter> for last cylinder or a number if you plan to create more. I actually typed the number even though I was just doing one (paranoia :-) )

11) Press w <enter> write to disk the partition Info

11a) #fdisk /dev/hda (again)

12) Press p <enter> shows all partion info (again, not shown in "m" help, but it this there. Verify your partitions are all set correctly.
Verify that partition 1 starts at cylinder 2 (it should if you followed step 9 correctly ;-)) and your blocks should match the size of the drive you want (since clusters
are set to 1024, this value will be something like 3999240 (which when multiplied by 1024 give you approx 4gb).

13) Press t <enter>

13a) Press 1 <enter> partition number
Press L <Enter> Will list all partion types ( as you will notice "b" is WIN95 FAT32, not sure what techincal difference this is with "c", but I am going with b...if you want ext2, then looks like "5" should be your choice...note skip quotes, they are just for clarity)

14) Press b ( as you will notice b is WIN95 FAT32)

15) Press w <enter> which writes again and then exits fdisk.
Extract Drive. (You can try ejecting it, but C860 doesn't seem to recognize it anyway.)

16) Format the drive using any of you favorite windows OS's, I used XP.
NOTE: I Don't know if you can format FAT32 witrh linux, but you can format ext2 with linux...I beleive the command is
$ mkfs.ext2 /dev/hda1 (but I am not a linux expert....just snagged that from some old cacko/crow pages and sustituted device.)

16a) Go back to step 7 if you want more than one partition (but don't forget to do step 0 again first (su- root)

17) Reboot Zaurus (Completely) and insert Microdrive.
(NOTE: If you do not see the drive in Zaurus "Contents" list, it is possible that you did not remember to format it per step 16)

18 )That's it, Now you will have access to the full 4 GB in BOTH Linux and Windows biggrin.gif biggrin.gif biggrin.gif

Special Thanks to (for extra clarity on Linux fdisk commands/issues):
Red Hat Linux 7.1: The Official Red Hat Linux Alpha Installation Guide
Prev Chapter 4. Installing Red Hat Linux
Their LINK: http://www.redhat.com/docs/manuals/linux/R...mode-fdisk.html[/b]

Please post if this helps you out or if not, so I know what problems you came across. (Feedback is always nice. smile.gif )
Go to the top of the page
+Quote Post
Start new topic
post Sep 7 2011, 09:25 PM
Post #2

Group: Members
Posts: 608
Joined: 14-April 04
Member No.: 2,853

Just wanted to mention that I updated these instructions (in original post above ) with a few comments and corrections, since I just had to do this for another drive I had lying around.
Go to the top of the page
+Quote Post

Posts in this topic

Reply to this topicStart new topic
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:


RSS Lo-Fi Version Time is now: 24th July 2014 - 11:25 AM