OESF Forums > Viewing Profile|
Profile
Personal Photo
Options
Personal Statement
Woland doesn't have a personal statement currently.
Personal Info
Woland
41 years old
Gender Not Set
Russian Jack, AK
Born April-1-1972
Interests
Getting my frigging Z to work!
Statistics
Joined: 9-October 04
Profile Views: 196*
Last Seen: 22nd November 2004 - 03:09 PM
Local Time: May 22 2013, 09:34 AM
5 posts (0 per day)
Contact Information
 No Information
 No Information
 No Information
 No Information
* Profile views updated each hour
|
Topics
Posts
Comments
Friends
My Content
10 Oct 2004
After a couple of months of my owning a beautiful 5500, I still can't connect up. I recompiled a bran spanking new 2.6.8 kernel, hotsync seems to work fine---when I turn on the Z in the cradel, usb0 is created and assigned the proper (static) IP address. Here is where the wierdness begins:
My ifconfig shows: CODE usb0 Link encap:Ethernet HWaddr 1A:60:19:07:1A:F0 inet addr:192.168.0.1 Bcast:192.168.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:22 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2502 (2.4 Kb) TX bytes:0 (0.0 b) And when I ping 192.168.0.1 I merrily ping away. Except the trafic does not go to usb0---it goes to the lo device. Gkrellm2 shows a big spike in traffic on lo when I ping, while usb0 remains silent! If I take lo down, then I can't ping. Here is the output of the route command: (komos is my firewall/gateway) CODE Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.0.0 * 255.255.255.0 U 0 0 0 usb0 10.1.1.0 * 255.255.255.0 U 0 0 0 eth0 default komos.momus.net 0.0.0.0 UG 0 0 0 eth0 The above is with lo down. With lo up, it looks like this: CODE Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.0.0 * 255.255.255.0 U 0 0 0 usb0 10.1.1.0 * 255.255.255.0 U 0 0 0 eth0 loopback localhost.local 255.0.0.0 UG 0 0 0 lo default komos.momus.net 0.0.0.0 UG 0 0 0 eth0 And, if it would help, here is the output of the netstat -rn command: CODE Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 usb0 10.1.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 127.0.0.0 127.0.0.1 255.0.0.0 UG 0 0 0 lo 0.0.0.0 10.1.1.1 0.0.0.0 UG 0 0 0 eth0 When I press either the "sync" button on the cradel, or "sync start" in the "PC Link" app, I get a short burst of traffic into usb0, followed by a "Communication was aborted" error on the Z. Unfortunately, I have no other way of getting software on the Z, so I can't even see what is going on there through a terminal. This is all very frustrating, so any ideas that you may have would be greatly appreciatesd. I tried adding a route manually: CODE route add -host 192.168.0.1 usb0 but that did nothing except add a useless entry in the routing table.I'm using the SHARP 3.10 ROM, if that helps. |
Last Visitors
Woland has no visitors to display.
Comments
Other users have left no comments for Woland.
Friends
There are no friends to display.
|
|
Lo-Fi Version | Time is now: 22nd May 2013 - 01:34 AM |