Help - Search - Members - Calendar
Full Version: Usb Networking
OESF Forums > Distros, Development, and Model Specific Forums > Distro Support and Discussion > pdaXrom
david_dahan
Hi ,

I just installed RC9 in my C750 , I am trying to connect (USB) the Z to a SuSE 9.2 machine but failed .
I can ping the Z from my desktop , the opposite way failed .
Can some one please send me a step by step procedure to setup the machines for a network connectivity .

thanks,
David.
Martin
Hi David,

before giving a hint it is neccesary to know which SuSE versing you are using ... because hotplug mechanism has changed (I think it was between 9.0 and 9.1/9.2) ...

you have to check some output at system console Ctrl-Alt-F10 while connecting Z to SuSE box ... look what output is at the end of /var/log/messages or post the dmest output ...

Good luck
Martin
david_dahan
QUOTE(Martin @ Apr 28 2005, 07:20 PM)
Hi David,

before giving a hint it is neccesary to know which SuSE versing you are using ... because hotplug mechanism has changed (I think it was between 9.0 and 9.1/9.2) ...

you have to check some output at system console Ctrl-Alt-F10 while connecting Z to SuSE box ... look what output is at the end of /var/log/messages or post the dmest output ...

Good luck
Martin
*



Hi Martin ,

Im using Suse 9.2 profetional , the following is the dmesg output :


Attached scsi removable disk sdd at scsi0, channel 0, id 0, lun 3
Attached scsi generic sg3 at scsi0, channel 0, id 0, lun 3, type 0
USB Mass Storage device found at 4
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usb0: register usbnet at usb-0000:00:1f.4-2.1.3, Sharp Zaurus, PXA-2xx based
usbcore: registered new driver usbnet
BIOS EDD facility v0.16 2004-Jun-25, 2 devices found
eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
NET: Registered protocol family 17
SFW2-IN-ILL-TARGET IN=usb0 OUT= MAC=fa:9b:da:91:3a:89:40:00:01:00:00:01:08:00 SRC=192.168.129.201 DST=192.168.129.200 LEN=84 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=6917 SEQ=2048
SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.168.254 DST=192.168.168.255 LEN=96 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=UDP SPT=137 DPT=137 LEN=76
SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.168.254 DST=192.168.168.255 LEN=96 TOS=0x00 PREC=0x00 TTL=64 ID=1 DF PROTO=UDP SPT=137 DPT=137 LEN=76
SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.168.254 DST=192.168.168.255 LEN=96 TOS=0x00 PREC=0x00 TTL=64 ID=2 DF PROTO=UDP SPT=137 DPT=137 LEN=76
SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.168.254 DST=192.168.168.255 LEN=96 TOS=0x00 PREC=0x00 TTL=64 ID=3 DF PROTO=UDP SPT=137 DPT=137 LEN=76
SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.168.254 DST=192.168.168.255 LEN=96 TOS=0x00 PREC=0x00 TTL=64 ID=4 DF PROTO=UDP SPT=137 DPT=137 LEN=76
SFW2-IN-ILL-TARGET IN=usb0 OUT= MAC= SRC=192.168.129.200 DST=192.168.129.255 LEN=96 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=UDP SPT=137 DPT=137 LEN=76
SFW2-IN-ILL-TARGET IN=usb0 OUT= MAC= SRC=192.168.129.200 DST=192.168.129.255 LEN=96 TOS=0x00 PREC=0x00 TTL=64 ID=1 DF PROTO=UDP SPT=137 DPT=137 LEN=76
SFW2-IN-ILL-TARGET IN=usb0 OUT= MAC= SRC=192.168.129.200 DST=192.168.129.255 LEN=96 TOS=0x00 PREC=0x00 TTL=64 ID=2 DF PROTO=UDP SPT=137 DPT=137 LEN=76
SFW2-IN-ILL-TARGET IN=usb0 OUT= MAC= SRC=192.168.129.200 DST=192.168.129.255 LEN=96 TOS=0x00 PREC=0x00 TTL=64 ID=3 DF PROTO=UDP SPT=137 DPT=137 LEN=76
ACPI: PCI interrupt 0000:00:1f.5[B] -> GSI 9 (level, low) -> IRQ 9
PCI: Setting latency timer of device 0000:00:1f.5 to 64
intel8x0_measure_ac97_clock: measured 182850 usecs
intel8x0: clocking to 48000
SFW2-IN-ILL-TARGET IN=usb0 OUT= MAC=fa:9b:da:91:3a:89:40:00:01:00:00:01:08:00 SRC=192.168.129.201 DST=192.168.129.200 LEN=84 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=6917 SEQ=3584
eth0: no IPv6 routers present
SFW2-IN-ILL-TARGET IN=usb0 OUT= MAC=fa:9b:da:91:3a:89:40:00:01:00:00:01:08:00 SRC=192.168.129.201 DST=192.168.129.200 LEN=84 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=6917 SEQ=3840
Device not ready. Make sure there is a disc in the drive.
Device not ready. Make sure there is a disc in the drive.
Device not ready. Make sure there is a disc in the drive.
Device not ready. Make sure there is a disc in the drive.
usb0: no IPv6 routers present
SFW2-IN-ILL-TARGET IN=usb0 OUT= MAC=fa:9b:da:91:3a:89:40:00:01:00:00:01:08:00 SRC=192.168.129.201 DST=192.168.129.200 LEN=84 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=6917 SEQ=4096
SFW2-IN-ILL-TARGET IN=usb0 OUT= MAC=fa:9b:da:91:3a:89:40:00:01:00:00:01:08:00 SRC=192.168.129.201 DST=192.168.129.200 LEN=84 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=6917 SEQ=4352
SFW2-IN-ILL-TARGET IN=usb0 OUT= MAC=fa:9b:da:91:3a:89:40:00:01:00:00:01:08:00 SRC=192.168.129.201 DST=192.168.129.200 LEN=84 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=6917 SEQ=4608
ACPI: Power Button (FF) [PWRF]
ACPI: Processor [CPU1] (supports C1)
powernow: This module only works with AMD K7 CPUs
Non-volatile memory driver v1.2
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
Device not ready. Make sure there is a disc in the drive.
Device not ready. Make sure there is a disc in the drive.
Device not ready. Make sure there is a disc in the drive.
Device not ready. Make sure there is a disc in the drive.
parport0: PC-style at 0x378 [PCSPP,TRISTATE,EPP]
lp0: using parport0 (polling).
drivers/usb/serial/usb-serial.c: USB Serial support registered for Generic
usbcore: registered new driver usbserial_generic
usbcore: registered new driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial Driver core v2.0
SFW2-IN-ILL-TARGET IN=usb0 OUT= MAC=fa:9b:da:91:3a:89:40:00:01:00:00:01:08:00 SRC=192.168.129.201 DST=192.168.129.200 LEN=84 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=7429 SEQ=0
SFW2-IN-ILL-TARGET IN=usb0 OUT= MAC=fa:9b:da:91:3a:89:40:00:01:00:00:01:08:00 SRC=192.168.129.201 DST=192.168.129.200 LEN=84 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=7429 SEQ=256
SFW2-IN-ILL-TARGET IN=usb0 OUT= MAC=fa:9b:da:91:3a:89:40:00:01:00:00:01:08:00 SRC=192.168.129.201 DST=192.168.129.200 LEN=84 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=7429 SEQ=512
SFW2-IN-ILL-TARGET IN=usb0 OUT= MAC=fa:9b:da:91:3a:89:40:00:01:00:00:01:08:00 SRC=192.168.129.201 DST=192.168.129.200 LEN=84 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=7429 SEQ=768
SFW2-IN-ILL-TARGET IN=usb0 OUT= MAC=fa:9b:da:91:3a:89:40:00:01:00:00:01:08:00 SRC=192.168.129.201 DST=192.168.129.200 LEN=84 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=7685 SEQ=0
SFW2-IN-ILL-TARGET IN=usb0 OUT= MAC=fa:9b:da:91:3a:89:40:00:01:00:00:01:08:00 SRC=192.168.129.201 DST=192.168.129.200 LEN=84 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=7685 SEQ=256
SFW2-IN-ILL-TARGET IN=usb0 OUT= MAC=fa:9b:da:91:3a:89:40:00:01:00:00:01:08:00 SRC=192.168.129.201 DST=192.168.129.200 LEN=84 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=7685 SEQ=512
SFW2-IN-ILL-TARGET IN=usb0 OUT= MAC=fa:9b:da:91:3a:89:40:00:01:00:00:01:08:00 SRC=192.168.129.201 DST=192.168.129.200 LEN=84 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=7685 SEQ=768
SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.168.254 DST=192.168.168.255 LEN=264 TOS=0x00 PREC=0x00 TTL=64 ID=1 DF PROTO=UDP SPT=138DPT=138 LEN=244
SFW2-IN-ILL-TARGET IN=usb0 OUT= MAC= SRC=192.168.129.200 DST=192.168.129.255 LEN=264 TOS=0x00 PREC=0x00 TTL=64 ID=1 DF PROTO=UDP SPT=138 DPT=138 LEN=244


thanks for responding.
David.
Martin
Hi :-)

My first intention is that your firewall is the problem ... try to add usb0 to the internal interface of the firewall ...

but you will get an error starting up your computer, if the Z is not connected at startup ... because interface usb0 did not exist if Z is not connected properly ...

Second thought was ... did you change your setting of USB working as USBnet device not USBmasstorage ... look inside the Z menu under System Tools / USB and change it to Network

Martin
david_dahan
QUOTE(Martin @ Apr 29 2005, 09:43 PM)
Hi :-)

My first intention is that your firewall is the problem ... try to add usb0 to the internal interface of the firewall ...

but you will get an error starting up your computer, if the Z is not connected at startup ... because interface usb0 did not exist if Z is not connected properly ...

Second thought was ... did you change your setting of USB working as USBnet device not USBmasstorage ... look inside the Z menu under System Tools / USB and change it to Network

Martin
*


Hi ,

I managed to establish a connection over the USB , I have ping working in both sides and able to synchronize Ka/Pi & Ko/Pi in the two machines.
Now I'm looking for a way to mount the storage devices of the Z on the Linux (SuSE9.2 pro) PC over NFS .
I thiks that I successfuly set up an NFS server on the PC but I will help in setting up NFS client on the Z .

thanks,
David.
david_dahan
QUOTE(david_dahan @ May 4 2005, 10:20 PM)
QUOTE(Martin @ Apr 29 2005, 09:43 PM)
Hi :-)

My first intention is that your firewall is the problem ... try to add usb0 to the internal interface of the firewall ...

but you will get an error starting up your computer, if the Z is not connected at startup ... because interface usb0 did not exist if Z is not connected properly ...

Second thought was ... did you change your setting of USB working as USBnet device not USBmasstorage ... look inside the Z menu under System Tools / USB and change it to Network

Martin
*


Hi ,

I managed to establish a connection over the USB , I have ping working in both sides and able to synchronize Ka/Pi & Ko/Pi in the two machines.
Now I'm looking for a way to mount the storage devices of the Z on the Linux (SuSE9.2 pro) PC over NFS .
I thiks that I successfuly set up an NFS server on the PC but I will help in setting up NFS client on the Z .

thanks,
David.
*




any suggestion ...... ?

David.
Stubear
Use samba, it's alread turned on by default on the Z when doing usb networking.

Or you can try the usb storage connection, but it only allows you to mount the SD or CF card - can't do both at once.

Stu
david_dahan
QUOTE(Stubear @ May 6 2005, 04:04 PM)
Use samba, it's alread turned on by default on the Z when doing usb networking.

Or you can try the usb storage connection, but it only allows you to mount the SD or CF card - can't do both at once.

Stu
*


Hi Stu ,

Thanks for replying . I have samba running on my Suse based PC (all WinXP PC's are visible) , I'm not sure that samba is running on the PDAX machine , ps aux | grep smb do not show any smb daemon running and smbstatus is not recognize.
Is samba server/client a part of RC9.1 ?
I looked on pdax feed , samba is presented bu there are many samba-codepage-xxx packages that I do not know what they are ....

cheers,
David.
Martin
Hallo Leute,

irgendwie steh ich grad auf dem Schlauch ... hab vor einigen Tagen ein Update von SuSE 9.2 auf 9.3 (mit neuem Kernel 2.6.11.4-20a-default) gemacht

Mein Zaurus hat bis jetzt einwandfrei mit hotplugscript über usbnet modul funktioniert ... jetzt geht nix mehr ... komischerweise funktioniert, erkennt aber der massstorage treiber und scsi emulation der Zaurus c860 im usb massenspeicher modus ...

seit dem funktionieren meine USB Maus und meine usbnet Anbinfung zum Zaurus nicht mehr ... USB Maus wird zwar durch hotplug erkannt, aber kein device zugewiesen und X kann nichts mit dem Eingabegerät anfangen.

Hat jemand eine Idee?

Hat sich am hotplug mechanismus seit SuSE 9.2 und altem kernel etwas geändert ... welche Rolle spielt dabei der neue udev mechanismus? Wieso funktioniert usbview nicht? Auch in /proc/.../usb/devices ist nicht drin ... *grummel*

Gruss
Marftin
david_dahan
QUOTE(Martin @ May 10 2005, 05:24 PM)
Hallo Leute,

irgendwie steh ich grad auf dem Schlauch ... hab vor einigen Tagen ein Update von SuSE 9.2 auf 9.3 (mit neuem Kernel 2.6.11.4-20a-default) gemacht

Mein Zaurus hat bis jetzt einwandfrei mit hotplugscript über usbnet modul funktioniert ... jetzt geht nix mehr ... komischerweise funktioniert, erkennt aber der massstorage treiber und scsi emulation der Zaurus c860 im usb massenspeicher modus ...

seit dem funktionieren meine USB Maus und meine usbnet Anbinfung zum Zaurus nicht mehr ... USB Maus wird zwar durch hotplug erkannt, aber kein device zugewiesen und X kann nichts mit dem Eingabegerät anfangen.

Hat jemand eine Idee?

Hat sich am hotplug mechanismus seit SuSE 9.2 und altem kernel etwas geändert ... welche Rolle spielt dabei der neue udev mechanismus? Wieso funktioniert usbview nicht? Auch in /proc/.../usb/devices ist nicht drin ... *grummel*

Gruss
Marftin
*


Hi Martin ,

Is it on the same subject ?

David.
david_dahan
QUOTE(david_dahan @ May 10 2005, 10:30 PM)
QUOTE(Martin @ May 10 2005, 05:24 PM)
Hallo Leute,

irgendwie steh ich grad auf dem Schlauch ... hab vor einigen Tagen ein Update von SuSE 9.2 auf 9.3 (mit neuem Kernel 2.6.11.4-20a-default) gemacht

Mein Zaurus hat bis jetzt einwandfrei mit hotplugscript über usbnet modul funktioniert ... jetzt geht nix mehr ... komischerweise funktioniert, erkennt aber der massstorage treiber und scsi emulation der Zaurus c860 im usb massenspeicher modus ...

seit dem funktionieren meine USB Maus und meine usbnet Anbinfung zum Zaurus nicht mehr ... USB Maus wird zwar durch hotplug erkannt, aber kein device zugewiesen und X kann nichts mit dem Eingabegerät anfangen.

Hat jemand eine Idee?

Hat sich am hotplug mechanismus seit SuSE 9.2 und altem kernel etwas geändert ... welche Rolle spielt dabei der neue udev mechanismus? Wieso funktioniert usbview nicht? Auch in /proc/.../usb/devices ist nicht drin ... *grummel*

Gruss


Marftin
*


Hi Martin ,

Is it on the same subject ?

David.
*




Dear All ,

I got samba working on my PdaX machine . Now I can see the C750 in the network .

many thanks for your help .

cheers,
David.
Martin
Hi david_dahan,

Sorry it was my mistake ... want to start a new thread ... because it is an other case with special fact ;-) ... but maybe someone other is able to help me

Are there other people with same problems on SuSE 9.3 ?

maybe it has something to do with the newer kernels ... I read a topic on "Openzaurus howto: usb networking" ... my problem is a little bit discribed there ... but can not get it work because no unconfigured usb0 is shown up ... lsusb not working, dmesg not showing any Z but recognizing a new device, Z shows up in usb storage mode.

Thanks a lot
Martin
This is a "lo-fi" version of our main content. To view the full version with more information, formatting and images, please click here.
Invision Power Board © 2001-2014 Invision Power Services, Inc.