Help - Search - Members - Calendar
Full Version: Sdhc Compatibility....
OESF Forums > General Forums > General Support and Discussion > Hardware Mods
deluxe
2 part question:
a) will there ever be compatibility such that the SDHC cards can be used in a zaurus?
b)is it possible to use regular SD cards that have a capacity greater than 4 GB (when/if they come out)??
Meanie
QUOTE(deluxe @ Feb 9 2007, 07:27 AM)
2 part question:
a) will there ever be compatibility such that the SDHC cards can be used in a zaurus?
b)is it possible to use regular SD cards that have a capacity greater than 4 GB (when/if they come out)??
*


a) never
cool.gif unlikely if you stay with Cacko or Sharp ROM
Drake01
QUOTE(deluxe @ Feb 8 2007, 04:27 PM)
b)is it possible to use regular SD cards that have a capacity greater than 4 GB (when/if they come out)??
*

I would be very surprised if they continue to develop the SD card for higher capacities. SDHC seems to be the new thing.
HoloVector
QUOTE(deluxe @ Feb 8 2007, 03:27 PM)
2 part question:
a) will there ever be compatibility such that the SDHC cards can be used in a zaurus?
b)is it possible to use regular SD cards that have a capacity greater than 4 GB (when/if they come out)??
*

This has been mentioned a few times already in forums.

SDHC has a hardware and and software components to it.

The software component is done and is availalble for the latest 2.6 kernel. It will eventually filter down to the Z ROMs based on 2.6 if it hasn't already been done. However, even when it does, it won't be too useful to the Z because the Z does not have the necessary SDHC hardware.

As far as greater than 4GB non-SDHC cards. Well, anything is possible but, I highly doubt it since the manufacturers have to closely follow the SD stardards so they can continue to use the SD trademark. Most manufacturers wouldn't consider it worth the legal hassle to produce non-SDHC high capacity cards.
Da_Blitz
but dosent sdhc require backwards compatability wink.gif

ie dosent it work with the slower speeds with just a software change, the only diffrence in terms of hardware is the call for a higher clock signal (4bit SD is 25Mhz max, i assume SDHC calls for double that or more). with a bit of req tweaking most equipment should do that.

that is if they are designed to be used with diffrent crystals, not sure about the pxa as they pretty much specify a 13Mhz crystal, i havent seen anything refering to another crystal speed that isnt the rtc and all the calcs assume a 13Mhz osscilator. that said it might be worth seeing if the registers allow you to change the timing on the SD hardware

i think we could make it work.
speculatrix
see my other post about flash card menagerie

I too would hope that an SDHC driver will become available for the Z, along with an SDIO driver too!

However, I think that getting it ported to Cacko is less likely than seeing it as part of OZ, pdaXrom or even Angstrom sad.gif
Meanie
QUOTE(speculatrix @ Mar 13 2007, 09:32 AM)
see my other post about flash card menagerie

I too would hope that an SDHC driver will become available for the Z, along with an SDIO driver too!

However, I think that getting it ported to Cacko is less likely than seeing it as part of OZ, pdaXrom or even Angstrom sad.gif
*


Actually, C3200 Sharp ROM has SDIO...
Jon_J
QUOTE(Meanie @ Mar 12 2007, 07:49 PM)
Actually, C3200 Sharp ROM has SDIO...
*

It does? !!
Where is it, and would I be able to use the Palm manufactured Wifi SD card that thousands of Palm users have?
Da_Blitz
the only dirver that exsists in the sharp implementation is for sdio serial, so basically your sdio gps reciver and thats about it (and barcode/rfid readers)
speculatrix
QUOTE(Da_Blitz @ Mar 13 2007, 07:29 AM)
the only dirver that exsists in the sharp implementation is for sdio serial, so basically your sdio gps reciver and thats about it (and barcode/rfid readers)
*


oooh!
well, that's a good start. anyone tried SDIO bluetooth card? then, you could fit wifi in CF slot, bt in sd slot, use a bt gps satnav and it'd be a great wardriving tool!
Da_Blitz
actually there is a profile definied by the SDHC people for bluetooth, so it mont be over serial most likley

actually USB and bluetooth are great because the guys who wrote the spec said "this is the interface between the driver and the hardware for device X, live with it" so most drivers work for everything. its only those a@#$% that decide to change one thing and then need a driver
speculatrix
I bought an sdio bluetooth card, relatively cheap off ebay, to try it out.

I will start a new thread.
Da_Blitz
actually the mont should be a wont, the rfid and barcode readers should just show up as a serial port. perhaps the we will get lucky with the bluetooth

any one have any idea how complete the SDHC driver is in the mainline kernel at the moment?
This is a "lo-fi" version of our main content. To view the full version with more information, formatting and images, please click here.
Invision Power Board © 2001-2014 Invision Power Services, Inc.