Help - Search - Members - Calendar
Full Version: Can't Get Desktop to Connect to SL-6000L
OESF Forums > General Forums > Desktop Operating Systems Issues > Linux Issues
rjray
I followed the Wiki page closely, installing usbnet-standalone. Turns out I already had a usbnet.o module, and when the standalone package didn't work, I tried the originally. I always get the same results. From my kernal messages log (I'm running Fedora Core 1,current kernel is kernel-smp-2.4.22-1.2199.nptl):

Oct 27 18:42:33 tzimisce kernel: hub.c: new USB device 00:1d.1-1.1, assigned address 37
Oct 27 18:42:33 tzimisce kernel: usb.c: USB device 37 (vend/prod 0x4dd/0x9032) is not claimed by any active driver.
Oct 27 18:42:36 tzimisce usb.agent[7766]: missing kernel or user mode driver acm
Oct 27 18:42:36 tzimisce kernel: sda: Unit Not Ready, sense:
Oct 27 18:42:36 tzimisce kernel: Info fld=0xa00 (nonstd), Current 00:00: sense key Not Ready
Oct 27 18:42:36 tzimisce kernel: sda : READ CAPACITY failed.
Oct 27 18:42:36 tzimisce kernel: sda : status = 1, message = 00, host = 0, driver = 08
Oct 27 18:42:36 tzimisce kernel: Info fld=0xa00 (nonstd), Current sd00:00: sense key Not Ready
Oct 27 18:42:36 tzimisce kernel: sda : block size assumed to be 512 bytes, disk size 1GB.
Oct 27 18:42:36 tzimisce kernel: sda: test WP failed, assume Write Enabled
Oct 27 18:42:36 tzimisce kernel: sda: I/O error: dev 08:00, sector 0
Oct 27 18:42:36 tzimisce kernel: I/O error: dev 08:00, sector 0
Oct 27 18:42:36 tzimisce kernel: unable to read partition table
Oct 27 18:42:37 tzimisce kernel: sda: Unit Not Ready, sense:
Oct 27 18:42:37 tzimisce kernel: Info fld=0xa00 (nonstd), Current 00:00: sense key Not Ready
Oct 27 18:42:37 tzimisce kernel: sda : READ CAPACITY failed.
Oct 27 18:42:37 tzimisce kernel: sda : status = 1, message = 00, host = 0, driver = 08
Oct 27 18:42:37 tzimisce kernel: Info fld=0xa00 (nonstd), Current sd00:00: sense key Not Ready
Oct 27 18:42:37 tzimisce kernel: sda : block size assumed to be 512 bytes, disk size 1GB.
Oct 27 18:42:37 tzimisce kernel: sda: test WP failed, assume Write Enabled
Oct 27 18:42:37 tzimisce kernel: sda: I/O error: dev 08:00, sector 0
Oct 27 18:42:37 tzimisce kernel: I/O error: dev 08:00, sector 0
Oct 27 18:42:37 tzimisce kernel: unable to read partition table
Oct 27 18:42:38 tzimisce devlabel: devlabel service started/restarted


And with all that, no actual connection between the two. I cannot create a usb0 interface device, and nothing new appears to kudzu (the new-hardware sniffer). I do have a module "acm.o" (under the usb hierarchy), but even with that force-loaded via modprobe, I get the above. I've had USB2.0 issues with flash drives, so I also tried plugging in the sync cable to a USB1.1 hub, to force it down to 1.1 when presented to the kernel (it's the only way I can get my Lexar to mount properly). Again, no difference.

I love this thing, but I'd like to be able to at least back it up. Actually exchanging data with my desktop would be just keen.

Randy
lardman
It looks like your desktop box thinks that the Z is a mass storage device.

What does 'lsmod' show on the Z?


Si
rjray
QUOTE(lardman @ Oct 28 2004, 09:29 AM)
What does 'lsmod' show on the Z?


pxa_bi
net_fd
usbdcore
prism2_usb
p80211
usbdmonitor
sharp_mmcsd_m
vtty
usb_ohci_tc6393
usbcore


Keep in mind, this is a factory-fresh SL-6000L. I haven't even been able to install the console application from the CD (I got the above via Konsole, downloaded from ZSI).

Randy
skoorb
are you using the docking station or direct usb from the sl-6000
rjray
Docking station...
skoorb
what linux os please ?

give us as specific info as possible!!

you already did, sorry, didn't look closely enough unsure.gif
lardman
QUOTE
Oct 27 18:42:36 tzimisce usb.agent[7766]: missing kernel or user mode driver acm
Oct 27 18:42:36 tzimisce kernel: sda: Unit Not Ready, sense:


I wonder if the first of these is important?

Do you have some other mass storage device attached (as this definitely looks like the sort of output I get when I attach my Z for mass storage).

I think it's possible with the 6000 to change to mass storage mode. Try doing this and attaching, then switch back and try attaching again (in net mode).


Si
This is a "lo-fi" version of our main content. To view the full version with more information, formatting and images, please click here.
Invision Power Board © 2001-2015 Invision Power Services, Inc.