[sdl]
# fulldouble -- Use double buffering.
# output -- Can only be Surface for the gp2x.
# sensitivity -- Mouse sensitivity.
# mapperfile -- File used to load/save the key/event mappings from.

fulldouble=false
output=surface
sensitivity=100
mapperfile=mapper.txt
usescancodes=false

[dosbox]

# machine -- The type of machine tries to emulate:hercules,cga,tandy,pcjr,vga.
# memsize -- Amount of memory dosbox has in megabytes.

machine=vga
memsize=4

[cpu]
# core -- CPU Core used in emulation: simple,normal,full.
# 			Try simple first as this is the fastest, then normal and last full
# cycles -- Amount of instructions dosbox tries to emulate each millisecond.
# 			Too low and the game will crash randomly / not start up
#			Too high and expect slowness
#			Just right and you will get a nice speed boost
#			600-1200 ish seems to be about the sweet spot for the things I've tested. (older games)
# cycleup   -- Amount of cycles to increase/decrease with keycombo.
# cycledown    Setting it lower than 100 will be a percentage.

core=simple
cycles=15000
#cycles=1500

[mixer]
# nosound -- Enable silent mode, sound is still emulated though.
# rate -- Mixer sample rate, setting any devices higher than this will
#         probably lower their sound quality.
# blocksize -- Mixer block size, larger blocks might help sound stuttering
#              but sound will also be more lagged.
# prebuffer -- How many milliseconds of data to keep on top of the blocksize.

nosound=true
rate=22050
blocksize=2048
prebuffer=30

[sblaster]
# sbtype -- Type of sblaster to emulate:none,sb1,sb2,sbpro1,sbpro2,sb16.
# sbbase,irq,dma,hdma -- The IO/IRQ/DMA/High DMA address of the soundblaster.
# mixer -- Allow the soundblaster mixer to modify the dosbox mixer.
# oplmode -- Type of OPL emulation: auto,cms,opl2,dualopl2,opl3.
#            On auto the mode is determined by sblaster type.
#            All OPL modes are 'Adlib', except for CMS.
# oplrate -- Sample rate of OPL music emulation.

sbtype=none
sbbase=220
irq=7
dma=1
hdma=5
mixer=true
oplmode=auto
oplrate=22050

[gus]
# gus -- Enable the Gravis Ultrasound emulation.
# gusbase,irq1,irq2,dma1,dma2 -- The IO/IRQ/DMA addresses of the 
#            Gravis Ultrasound. (Same IRQ's and DMA's are OK.)
# gusrate -- Sample rate of Ultrasound emulation.
# ultradir -- Path to Ultrasound directory.  In this directory
#             there should be a MIDI directory that contains
#             the patch files for GUS playback.  Patch sets used
#             with Timidity should work fine.

gus=false
gusrate=22050
gusbase=240
irq1=5
irq2=5
dma1=3
dma2=3
ultradir=C:\ULTRASND

[speaker]
# pcspeaker -- Enable PC-Speaker emulation.
# pcrate -- Sample rate of the PC-Speaker sound generation.
# tandy -- Enable Tandy Sound System emulation (off,on,auto).
#          For auto Tandysound emulation is present only if machine is set to tandy.
# tandyrate -- Sample rate of the Tandy 3-Voice generation.
# disney -- Enable Disney Sound Source emulation.

pcspeaker=true
pcrate=22050
tandy=auto
tandyrate=22050
disney=true

[dos]
# xms -- Enable XMS support.
# ems -- Enable EMS support.
# umb -- Enable UMB support (false,true,max).

xms=true
ems=false
umb=false

[autoexec]
# lines of code to boot the dos program go here