OESF Portables Forum

Everything Else => General Support and Discussion => Zaurus General Forums => Archived Forums => Software => Topic started by: jdev on March 07, 2005, 09:35:06 am

Title: Wellenreiter Scans
Post by: jdev on March 07, 2005, 09:35:06 am

I am using Cacko Zaurus Qtopia Rom 1.21a incase it is any help to anyone.

I was able to get wellenreiter installed on my zaurus.  after some initial problems where it would tell me that it couldnt initiate eth0 because a file or directory could not be found, I finally got wellenreiter to scan.

problem is, is that its not picking up any networks.  I know many of you are asking, well, are you in a wifi area?  yes.  Kismet picks up the 2 networks nearest to me at the office, while wellenreiter, though the title bar shows scanning, does not.

my question is, is it possible that I have wellenreiter configured incorrectly?  could someone share with me the correct config for wellenreiter?  also, does wellenreiter require a certain signal from a wifi network?  the signal on one of the networks is rather low, while one is fair.

tia.

Title: Wellenreiter Scans
Post by: Bertram Wooster on March 07, 2005, 10:20:02 am

have a look here:
https://www.oesf.org/index.php?title=Wellen...topia_based_ROM (https://www.oesf.org/index.php?title=Wellenreiter_on_Qtopia_based_ROM)
this tutorial worked perfectly for me, maybe it'll help you, too

Title: Wellenreiter Scans
Post by: jdev on March 07, 2005, 01:22:29 pm

Quote

have a look here:
https://www.oesf.org/index.php?title=Wellen...topia_based_ROM (https://www.oesf.org/index.php?title=Wellenreiter_on_Qtopia_based_ROM)
this tutorial worked perfectly for me, maybe it'll help you, too
[div align=\"right\"][a href=\"index.php?act=findpost&pid=69624\"][{POST_SNAPBACK}][/a][/div]

thank you for the tutorial.  I went through, uninstalling libpcap, libopie1 and 2, and wellenreiter.  I attempted to install each package from the tarball, to no avail.  When i first tried to install libpcap, it told me that there may be other dependancies, and I should install them as well.  I tried to forge on and install the libopie libraries, but, to no avail.

the error message I am getting with ipkg is "ipkg says something went wrong. sorry"

this has been happening for a few days now, i will make a different post about that.

in any event.  I connected to the cacko feed and re-installed wellenreiter.  I can run it again with the changes made to the confs and all that, but, still nothing.  It scans, but, does not discover a network, whereas kismet picks up 2 still.

Title: Wellenreiter Scans
Post by: seinfield on March 13, 2005, 04:17:51 pm

Download Wellenreiter with libs from the zug downloads, then replace the Wellenreiter with the wellenreiter from the cacko feed.
Follow the install instructions from zug downloads, then create a dummy connection. execute Wellenreiter and autodetect your wifi card.
And Thats all.

Easy!!!
It worked for me.
I have a C700 with cacko 1.22 with hotfix

Title: Wellenreiter Scans
Post by: shaolin on April 02, 2005, 06:03:27 am

yop i follow your instructions  Siendfield i have the same conf but :


when i launch a sniffer he cant detect any networkz


but it workz with kitsmet ...

coud u plz explain what conf did u choose ? hostap ? or  ? wlan ?


wifi or ether ?


thx a lot

Title: Wellenreiter Scans
Post by: shaolin on April 02, 2005, 06:25:51 am

Its Workz now  thx for support