OESF Portables Forum

Everything Else => Sharp Zaurus => Model Specific Forums => Distros, Development, and Model Specific Forums => Archived Forums => C1000/3x00 General discussions => Topic started by: offroadgeek on May 01, 2005, 10:22:32 pm

Title: Can't Get 1000 Into Service Menus
Post by: offroadgeek on May 01, 2005, 10:22:32 pm

I can't seem to get my 1000 into the service menus.  I've been doing the standard D+M after taking out the batter for 30 seconds, then re-inserting the battery and connecting the power...  

I was going to flash to OZ to check it out but wanted to make a NAND backup first and simply make sure I could access the menu in case anything bad happened.

So, has any other 1000 users been able to access the service menus?

Title: Can't Get 1000 Into Service Menus
Post by: lpotter on May 01, 2005, 11:07:10 pm

Quote

I can't seem to get my 1000 into the service menus.  I've been doing the standard D+M after taking out the batter for 30 seconds, then re-inserting the battery and connecting the power...   

I was going to flash to OZ to check it out but wanted to make a NAND backup first and simply make sure I could access the menu in case anything bad happened.

So, has any other 1000 users been able to access the service menus?
[div align=\"right\"][a href=\"index.php?act=findpost&pid=77809\"][{POST_SNAPBACK}][/a][/div]

the c3000 is d + m + reset button. Don't 'power on', the diag menu will come up ..

Title: Can't Get 1000 Into Service Menus
Post by: iamasmith on May 02, 2005, 06:26:46 am

Here's what I found with the 3K, I guess it should be equally applicable to the 1K.

It's under this section of the Wiki and covers D+B and D+M booting.

https://www.oesf.org/index.php?title=C3000_...lashing_process (https://www.oesf.org/index.php?title=C3000_Device_Specifics#Examining_the_flashing_process)

Title: Can't Get 1000 Into Service Menus
Post by: TRIsoft on May 02, 2005, 09:37:39 am

Offroadgeek,
the trick is that the Zaurus must "see" the keys in the
moment he got's power.
So press the keys with no battery/ac. Then plug the
battery in WHILE the keys are pressed.
Flip the battery switch and you should see the Diag.

///TRIsoft

Marc Stephan

Title: Can't Get 1000 Into Service Menus
Post by: Ragnorok on May 02, 2005, 08:46:05 pm

You *go* Trisoft.  Thanks!

Title: Can't Get 1000 Into Service Menus
Post by: offroadgeek on May 03, 2005, 12:33:06 pm

Yep, that was my problem.  I was putting the battery in before I was pressing D + M.  Silly me!

thanks

Title: Can't Get 1000 Into Service Menus
Post by: me@home on November 27, 2005, 02:20:00 pm

I tried to do this Nand Backup for the 1st time and the Z didn't recognise my 2GB Fat16 CF Kingston Elite Pro...grrr

Well I seached for an old CF I have for a my digital camera, a Sandisk Ultra II 256MB, did OK and I the backup was over in 4-5 min.

Maybe I should have done this before I flashed to Cacko 1.23?
Hmm, I just got the file from Trisoft (thx for sharing !), hope it'll work OK if I ever need to flash back to Sharp.

May I ask ? When I reseize the flash (like I did during Cacko installation) and then reflash to 'original' Rom is the the flash reseized automatically ? I ask because when I want to try pdx I have to reseize again...