OESF Portables Forum
Everything Else => Sharp Zaurus => Model Specific Forums => Distros, Development, and Model Specific Forums => Archived Forums => C1000/3x00 General discussions => Topic started by: bar0n on June 22, 2005, 05:47:14 am
-
Hi all,
I've read a couple of posts regarding the Symbol Spectrum CF card on the C1000. I have successfully connected to my home and work APs without using WEP. However, when I enable WEP, I cannot connect.
I use "iwconfig eth0 key xxxxxxxx".
iwconfig shows the correct WEP key, but alas no luck. Anyone else had this?
Secondly, I'd like to use a wireless sniffer - Kismet, Wellenreiter or such.
I've set my capture source to wlanng,eth0,test and get ETH0: Device or Resource Busy. Setting to wlanng,wlan0,test gets: Interface wlan0: no such device.
I've tried setting up a dummy wireless connection as suggested elsewhere, but still no joy.
Wellwenreiter gives me SIOCSIFFLAGS: Device or resource busy. using eth0
I've tried entering my cardctl ident info into wlan-ng.conf.
Tearing my hair our now
Does anyone else have this combination working with WEP and with a sniffer?
Thanks in advance!
Bar0n
-
Wait for Cacko ROM release for C1000, this card is well supported. And new card version too, BTW
-
That is soo cool. Do you know if there is any real advantage with the new one?
...... And new card version too, BTW
[div align=\"right\"][a href=\"index.php?act=findpost&pid=85584\"][{POST_SNAPBACK}][/a][/div]
-
Thanks maslovsky,
I thought that Cacko ROM would be an answer. I'm desperately waiting to move on to Cacko. Is it likely to be available within the next few months?
Thanks
Mark
-
Wait for Cacko ROM release for C1000, this card is well supported. And new card version too, BTW
[div align=\"right\"][a href=\"index.php?act=findpost&pid=85584\"][{POST_SNAPBACK}][/a][/div]
any clue on support in pdaXrom?
-
Secondly, I'd like to use a wireless sniffer - Kismet, Wellenreiter or such.
Hi,
I am also trying to get Wellenriter or KismEt to work with a Symbol/spectrum card. (After 15 years on computers I am still having problems with my spectrum)
I have wellenriter acquiring packets by ding the command, as su :-
iwconfig eth0 mode "AD-HOC"
iwconfig eth0 essid "Any"
And to resuem normal networking
iwconfig eth0 mode "AD-HOC"
iwconfig eth0 essid "what_ever_network_you_use"[/code]
Or
iwconfig eth0 essid "ANY"
Unfortunately, the sniffed packets are shown as 'Wired' packets not wireless. Time for me to RTFN.
Hope this helps,
Brendan
-
Thanks maslovsky,
I thought that Cacko ROM would be an answer. I'm desperately waiting to move on to Cacko. Is it likely to be available within the next few months?
Thanks
Mark
[div align=\"right\"][a href=\"index.php?act=findpost&pid=85666\"][{POST_SNAPBACK}][/a][/div]
Yes, definitely!
-
Wait for Cacko ROM release for C1000, this card is well supported. And new card version too, BTW
[div align=\"right\"][a href=\"index.php?act=findpost&pid=85584\"][{POST_SNAPBACK}][/a][/div]
any clue on support in pdaXrom?
[div align=\"right\"][a href=\"index.php?act=findpost&pid=85715\"][{POST_SNAPBACK}][/a][/div]
Sorce code for the drivers is available with Archos SDK (they use this card in their device), so it shouldn't be a problem to support this card in pdaxrom too.