OESF Portables Forum
Everything Else => Zaurus Distro Support and Discussion => Distros, Development, and Model Specific Forums => Archived Forums => Angstrom & OpenZaurus => Topic started by: dranath on August 11, 2005, 09:19:48 am
-
Hello Forum,
today I flashed from the original Sharp-ROM because I wanted to give OpenZaurus and OPIE a try. But there are several things where I didn't find my way around:
Problem 1:
After setting up my "Network Settings" for Wireless-LAN (interface "wlan0") and hit the "Start/Stop"-button, I get the message:
"Starting interface failed"
Anyway, the WLAN-LED lights up green and when I leave the "Network Settings" and enter them again the 802.11b-connection is indicated "up". Also if I hit the "Start/Stop"-button again, there is a register-tab called "802.11b" with status-information about my connection (I even see the Quality of the WLAN-connection decline if I shild the built in antenna with my hands).
So I tried to connect to a web-site using Konqueror, but after some time I recieved the message
"Unknown host www.web.de"
---
This brought me to Problem 2:
I tried to get some information from "/etc/resolv.conf", but to get there was tricky because when I wanted to start the "Console" application in the "Applications"-tab it doesn't start but displays the message:
"Console was terminated due to signal code SIGSEGV"
How can I fix this to use the console-application from "inside" OPIE?
---
Back to the original "Problem Number One":
Alternatively I logged into the console via the "Start"-menu choosing "Terminal -> 1" and issued
# cat /etc/resolv.conf
to check my DNS-settings - but everything looked like it should.
An
# ifconfig
told me that "wlan0" is up (with all the network-settings I previously put into my machine), but a
# ping -c 5 www.web.de
produced the message
ping: www.web.de: Host name lookup failure
---
After some time the screen turned darker and darker (I suppose the screen dimmed with the OPIE-timer even if I was in the "Terminal") and I hardly could make out what my machine was replying to my inquiries (not even button-pressing brought the screen back to light).
So my Problem 3 is:
How do I get back to OPIE after I locked into the Terminal from the "Start"-menu?
Thanks in advance for your help
dranath
-
Hello again,
I think I forgot which Software my Zaurus SL-6000 (Tosa) runs on:
OpenZaurus 3.5.3
with
OPIE 1.2.0.
Also I tried to reflash the installation and after the OpenZaurus "Zaurilla" appears I saw following error messages (???) float by on the boot-screen [1], [2]:
dpemoa: *** Unresolverd symbols in /lib/modules/2.4.14-rmk7-pxa3-embedix/linux-lan-ng/prism2_pci.o
[1] only the first time I booted after the flashing of the Zaurus
[2] maybe not 100-percent correct to the letter because I didn't know how to pause the display - and off it went...
Hope this helps
Thanks
dranath
-
Hello Forum,
today I flashed from the original Sharp-ROM because I wanted to give OpenZaurus and OPIE a try. But there are several things where I didn't find my way around:
Problem 1:
After setting up my "Network Settings" for Wireless-LAN (interface "wlan0") and hit the "Start/Stop"-button, I get the message:
"Starting interface failed"
*SNIP*
Thanks in advance for your help
dranath
[div align=\"right\"][a href=\"index.php?act=findpost&pid=91478\"][{POST_SNAPBACK}][/a][/div]
Look thru the directions for OZ/Opie again. They mention that you need to start and stop the WiFi via console commands:
ifup wlan0
ifdown wlan0
My 6000 has worked randomly via the wifi GUI. I am used to executing via the console at this point.
Regards,
jawZ
-
Look thru the directions for OZ/Opie again. They mention that you need to start and stop the WiFi via console commands:
ifup wlan0
ifdown wlan0
My 6000 has worked randomly via the wifi GUI. I am used to executing via the console at this point.
Regards,
jawZ
Thank you for this information. But this brings me to the other problems I described (they are "quasi-recursive" :-).
Since
a) the GUI-Console doesn't start (a.k.a. "Problem 2")
and
b) I don't know how to get back to OPIE after I went into the terminal (a.k.a. "Problem 3"),
this doesn't help me at all.
Thanks
dranath
-
How can I fix this to use the console-application from "inside" OPIE?
I don't know why this is happening to you - I'd ask on IRC or the ml as you may get a proper answer - anyway you could either change vt (which you've tried), or ssh into the machine or use the shut down applet to quit Opie.
So my Problem 3 is:
How do I get back to OPIE after I locked into the Terminal from the "Start"-menu?
There's a command you can issue on the command line to go back to vt 2 (which is where Opie is running) and also a keypress. I'm afraid I can't remember either, but a search for 'vt' should find the answer,
Si