OESF Portables Forum
Model Specific Forums => Sharp Zaurus => Zaurus - pdaXrom => Topic started by: badog on October 14, 2005, 10:38:29 am
-
my friend installed rc11 in c3100;
c3100 was breaked! can't to D-M.
where download c3100 fix-nandrom?
-
my friend installed rc11 in c3100;
c3100 was breaked! can't to D-M.
where download c3100 fix-nandrom?
[div align=\"right\"][a href=\"index.php?act=findpost&pid=99360\"][{POST_SNAPBACK}][/a][/div]
check www.trisoft.de for the nand rom ( make sure, you get the right file - do not use the C1000 or C3000 one!!!)
-
it can't into D-M mode.so i cant restore nandrom from some backup file
-
sashz released a bootfix of sorts to fix this issue on a big "oops" search the forums for the first release of pdaxrom for the 3100
-
SASHZ:help me,please
-
http://212.10.30.205/rc10/sashz/test/recover-3100.tar.bz2 (http://212.10.30.205/rc10/sashz/test/recover-3100.tar.bz2)
1) unpack files on the FAT16 CF or SD card.
2) power off power supply, pull out battery
3) Press C and D keys, hold this keys and insert battery
4) Led must flash on and off
5) Reinsert battery and run Z with [OK] button for reflash with new system
-
Thank you,very much
-
http://212.10.30.205/rc10/sashz/test/recover-3100.tar.bz2 (http://212.10.30.205/rc10/sashz/test/recover-3100.tar.bz2)
...
[div align=\"right\"][{POST_SNAPBACK}][/a][/div] (http://index.php?act=findpost&pid=99504\")
Thank you for making a promising rom. However after trying rc11 and briefly rc12 on my C3100 I wanted to go back to the Sharp rom and got hit by this bootloader problem!
Could someone please clarify what the above isntructions do?
Basically I want to go back to the Sharp rom. I've downloaded the NAND backup from TriSoft, but I can't into the service menu (D+M). So I followed the above instructions, but I still can't get into the D+M menu, I keep booting back into pdaXrom when I switch the machine on.
I'm new to all this, this is my first Zaurus and I've only had it a couple of days, so if someone could kindly instruct me how to restore the Sharp rom I would be very grateful
(BTW please someone, update the instructions here [a href=\"http://www.pdaxrom.org/index.php?showid=42&menuid=11]http://www.pdaxrom.org/index.php?showid=42&menuid=11[/url] so that C3100 owners are warned about the consequences of changing the bootloader!)
cheers
-- desert rat
-
you are removeing the battery and power before pressing d+m right?
-
you are removeing the battery and power before pressing d+m right?
[div align=\"right\"][{POST_SNAPBACK}][/a][/div] (http://index.php?act=findpost&pid=99526\")
Yep. In fact I've tried 3 different procedures -- the 2 outlined here:
[a href=\"http://www.trisoft.de/en_c3100howto.htm]http://www.trisoft.de/en_c3100howto.htm[/url]
And the seemingly simpler method on page 30 of TriSoft's quick start guide. The 3 procedures are detailed below:
1) Power down the Zaurus and remove all power sources (no AC adaptor and remove the battery!). Set the battery switch to the "Offen" position and wait for at least 5 seconds. Then connect the AC adaptor and put back the battery. Hold down the [D] and [M] keys and set the battery switch back to "Betrieb" (while keys are pressed!). After a short moment the diagnostics menu should appear.
No service menu, boots into pdaXrom.
2) If not, try it again and this time hold down the [D] and [M] keys before you restore the power (AC adaptor / battery).
This procedure was tricky, how do you keep the D+M keys pressed whilst inserting the battery and plugging in the AC power? Anyway I tried it a few times and I think I managed it, but still no service menu
3) Set the battery switch to "Offen" and wait a couple of seconds. Connect the Zaurus to a power source (USB cable or power supply), hold down the keys "D" and "M" and switch back to "Betrieb"
Now this one doesn't explicitly say remove the battery, if this is correct, it would be a easiest to perform. But still I couldn't get the service menu.
Sorry if this sounds stupid -- in all 3 methods it doesn't explicitly say you have to press the on/off button (as a last step) -- I'm assuming that you do because if it wasn't pressed then nothing happens.
What is the "official"/definitive method of accessing the service menu?
thanks
-- desert rat
-
(BTW please someone, update the instructions here http://www.pdaxrom.org/index.php?showid=42&menuid=11 (http://www.pdaxrom.org/index.php?showid=42&menuid=11) so that C3100 owners are warned about the consequences of changing the bootloader!)
[div align=\"right\"][a href=\"index.php?act=findpost&pid=99520\"][{POST_SNAPBACK}][/a][/div]
Strange, after reading more of the forum it appears that the bootloader bug was fixed in/by rc11. Nevertheless, I'm unable to access the D+M service menu.
-- desert rat
-
What is the "official"/definitive method of accessing the service menu?
[div align=\"right\"][{POST_SNAPBACK}][/a][/div] (http://index.php?act=findpost&pid=99544\")
OK I've got it now. The instructions here seemed clearest:
[a href=\"http://downloads.conics.net/pda/zaurus-sl-c700/service-menus/]http://downloads.conics.net/pda/zaurus-sl-.../service-menus/[/url]
In my case I kept the D & M buttons pressed and as soon as I inserted the battery the service menu appeared.
cheers
-- desert rat