OESF Portables Forum
Everything Else => Sharp Zaurus => Model Specific Forums => Distros, Development, and Model Specific Forums => Archived Forums => C1000/3x00 General discussions => Topic started by: miloo on May 24, 2006, 04:58:10 am
-
Hello. I read here and there all the problems people have with their zaurus and wifi 802.11b cards that connect badly to access points when in mixed b/G mode. They fix the problem by forcing b-mode only.
As I have an 802.11g AP (linksys WRT54g) that I want to keep as g-mode since I use it at max speed, I would want to know if it would be possible to add a 802.11b access point that would be connected to it, that would be dedicated to b-mode connections only, so that accessing my internal network with the zaurus with a 802.11b wifi card (like a planex cf11x or ambicom wl1100c for ex.) would not prevent from using the main access point as 802.11g.
PS : I ask this because I plan to buy a wifi card but I don't want to be bothered by such problems and am ready to buy a 802.11b AP if it can help me.
Eric
-
One easy way is it set the AP connect to the specific ESSID and/or set it to only look on the specific channel the 802.11b AP is set to...
-
miloo: read about WDS (Wireless Distribution System) where few AP work with same essid and settings - you will make one G-only and second B-only.
-
Miloo:
The Linksys WCF54G Wireless-G CompactFlash card is hoped to be working with OpenZaurus in the near future (see this thread (https://www.oesf.org/forums/index.php?showtopic=19469))
Thanks again, Hrw!
-
I do have two AP (one g and one . I have no problems with any of my Zs connecting to the b. A g card would be cool......
-
miloo: read about WDS (Wireless Distribution System) where few AP work with same essid and settings - you will make one G-only and second B-only.
[div align=\"right\"][a href=\"index.php?act=findpost&pid=128425\"][{POST_SNAPBACK}][/a][/div]
The problem with WDS is it works by making both routers act as repeaters. Any traffic one receives, it sends to the other. Having B clients degrades performance on a G network, so performance will always be degraded because the two routers are always going to be repeating to each other. This rather defeats the original poster's purpose of having a seperate network so as not to degrade the G network's speed.
You'd want to link both AP's to a wired network instead, and make sure they are using different frequencies (and SSIDs) so they don't interfere with each other.
-
One easy way is it set the AP connect to the specific ESSID and/or set it to only look on the specific channel the 802.11b AP is set to...
[div align=\"right\"][a href=\"index.php?act=findpost&pid=128423\"][{POST_SNAPBACK}][/a][/div]
Thank you for all answers. It seems that's not so obvious ...
InSearchOf : so you wire the 802.11b AP to the 802.11g, and using a different ESSID for the 802.11b, the zaurus should connect to it, and thus be connected to the network without having effect on the speed of the 802.11g AP ? Is that true ?
-
just a little tidbit I found at toms hardware
toms hardware as tips on this (http://www.tomsnetworking.com/2006/06/26/wireless_faq_setup_and_configuration/page4.html#453)
You'll need to do the following to set this up:
- Use only channels 1, 6, or 11 and set the 11b and 11g APs to different channels.
- Disable 11b protection on the 11g-only AP (this is frequently called 11g-only mode)
- Set each AP to a different SSID (not essential, but helps for troubleshooting purposes)