OESF Portables Forum

Everything Else => General Support and Discussion => Zaurus General Forums => Archived Forums => Accessories => Topic started by: LukeLuke on August 01, 2006, 05:19:47 am

Title: Anyone Has Try A Usb To Eth Adaptor On C1000?
Post by: LukeLuke on August 01, 2006, 05:19:47 am
Hello, i bougth a C1000 and i would buy this accessories :

http://cgi.ebay.it/USB-to-LAN-RJ45-Etherne...1QQcmdZViewItem (http://cgi.ebay.it/USB-to-LAN-RJ45-Ethernet-10-100-Mbps-Network-Adaptor_W0QQitemZ290014071458QQihZ019QQcategoryZ51195QQrdZ1QQcmdZViewItem)

Someone has try this periferic ? Work ?

THANKS

Bye
Title: Anyone Has Try A Usb To Eth Adaptor On C1000?
Post by: hus on August 01, 2006, 05:25:56 am
Quote
Hello, i bougth a C1000 and i would buy this accessories :

http://cgi.ebay.it/USB-to-LAN-RJ45-Etherne...1QQcmdZViewItem (http://cgi.ebay.it/USB-to-LAN-RJ45-Ethernet-10-100-Mbps-Network-Adaptor_W0QQitemZ290014071458QQihZ019QQcategoryZ51195QQrdZ1QQcmdZViewItem)

Someone has try this periferic ? Work ?

THANKS

Bye
[div align=\"right\"][a href=\"index.php?act=findpost&pid=137127\"][{POST_SNAPBACK}][/a][/div]

it looks exactly the same one i have, (not sure about the brand) but it looks the same

i use it with *SL-C3200* works ok, with OpenBSD works but the screen throwing lots of errors and after while it looks up the connection
Title: Anyone Has Try A Usb To Eth Adaptor On C1000?
Post by: LukeLuke on August 01, 2006, 05:28:22 am
the screen-shot in the auction tell that windows recognize the HW so ADMtek ADM8511.

Work with pdaXrom ?

THANKS

Bye
Title: Anyone Has Try A Usb To Eth Adaptor On C1000?
Post by: LukeLuke on August 01, 2006, 05:31:02 am
Quote
it looks exactly the same one i have, (not sure about the brand) but it looks the same

i use it with *SL-C3200* works ok, with OpenBSD works but the screen throwing lots of errors and after while it looks up the connection
[div align=\"right\"][a href=\"index.php?act=findpost&pid=137128\"][{POST_SNAPBACK}][/a][/div]

Wich module load it ?

THANKS

Bye

P.S. Work without the supplied USB HUB  ?
Title: Anyone Has Try A Usb To Eth Adaptor On C1000?
Post by: hus on August 05, 2006, 03:10:18 am
Quote
Wich module load it ?

THANKS

Bye

P.S. Work without the supplied USB HUB  ?
[div align=\"right\"][a href=\"index.php?act=findpost&pid=137130\"][{POST_SNAPBACK}][/a][/div]

aaah! so sorry for late replay, i was busy lately with my research!

in openbsd it appear as ause0, no need a USB HUB

but as i said it throw lots of errors and after while stop and i need to unplug it and plug it again. (software issue it may because of my configuration)
Title: Anyone Has Try A Usb To Eth Adaptor On C1000?
Post by: Da_Blitz on August 05, 2006, 06:39:23 am
i have had USB devices that draw too much power make my pda unstable under linux (OZ 2.6 kernel)

once i plugged it into a powered hub it worked fine, without the hub it worked but when transfering data it would fill the kernel log with messages amout the device reseting itself and my net connection would go down
Title: Anyone Has Try A Usb To Eth Adaptor On C1000?
Post by: Lurker on August 07, 2006, 12:48:26 pm
The GNU/Linux "usbnet" Driver Framework (http://www.linux-usb.org/usbnet/) site is an excellent reference for USB-to-Ethernet and Linux.
Title: Anyone Has Try A Usb To Eth Adaptor On C1000?
Post by: LukeLuke on September 22, 2006, 08:47:08 am
the gadgets is arrived it is an ST268 USB NIC, when i use it on pdaXrom it's not work!

What can i do ?

Code: [Select]
root@zaurus ~# lsusb -v

Bus 001 Device 014: ID 0a46:0268 Davicom Semiconductor, Inc.
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               1.10
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0         8
  idVendor           0x0a46 Davicom Semiconductor, Inc.
  idProduct          0x0268
  bcdDevice            1.01
  iManufacturer           1 ShanTou
  iProduct                2 ST268 USB NIC
  iSerial                 3 0268
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           39
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xa0
      Remote Wakeup
    MaxPower              144mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           3
      bInterfaceClass         0 (Defined at Interface level)
      bInterfaceSubClass      0
      bInterfaceProtocol      0
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               none
          Usage Type               Data
        wMaxPacketSize     0x0040  bytes 64 once
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x02  EP 2 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               none
          Usage Type               Data
        wMaxPacketSize     0x0040  bytes 64 once
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x83  EP 3 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               none
          Usage Type               Data
        wMaxPacketSize     0x0008  bytes 8 once
        bInterval               1
  Language IDs: (length=4)
     0409 English(US)
THANKS

Bye