OESF Portables Forum
Model Specific Forums => Sharp Zaurus => Zaurus - pdaXrom => Topic started by: conundrum on April 11, 2007, 03:37:27 pm
-
Well, my conics.net C3200 just came in, I'm downloading pdaXii13 as we speak, and copying all my own little tweaks and configurations from my 860 to a SD card. This will be my third Zaurus (the fist being a 5500 that ran OZ), I know enough to admit I know nothing about this model, and ask for advice and warnings.
My planned setup is to keep my 1 GB SD card and use the CF slot exclusively for wireless. I think 7 gigs should be more than enough storage. However, this is where the performance questions come up. Should I install packages to internal flash, the internal drive, or SD? It's a SanDisk Ultra II, if the Zaurus bus can actually utilize the increased speed.
Basically, for those of you short in attention span or patience: what should I install (and how/where), what should I avoid doing, and what do I need to know about the 3200?
-
I'm not going to tell you to do this my way, but you can probably try a variation of my method.
On my C3200, I installed pdaxii13-akita on NAND
First you must install pdaxrom beta 3 to get pdaxii13 working, I think it needs the pdaxrom kernel from beta 3. (I don't know if this has changed recently, but when pdaxii13 first came out, it was only for the C3000, and users of other models needed to install pdaxrom beta 3 first)
http://www.users.on.net/~hluc/myZaurus/pdaxii13.html (http://www.users.on.net/~hluc/myZaurus/pdaxii13.html)
Once pdaxrom beta 3 is installed, you don't have to setup anything, just use the pdaxii13 files and reflash to pdaxii13
OK, this is the way I'm running pdaxii13-akita on NAND
What I did, was install small apps and utilities to flash, and I installed large apps, (like Firefox) onto the microdrive.
This gives me an OS and utilities that runs entirely from flash. This has a quicker response than installing everything to the hard drive.
-
That sounds a lot like what I was doing on my 860. The small, important apps ran from flash, and the larger, less critical ones from SD.
If I Ihave to install beta 3 first that might explain the error I've been getting trying to simply install pdaXii through the normal pdaX manner (booting from the Japanese flash new ROM menu into the pdaX installeer and running the NAND fix utility, followed by Install new ROM).
-
What I would do, partitioning-wise, is have a smallish partition for installing stuff to, a smallish swap partition, and have the rest be for data. Format the data and install partitions as EXT2 (data can be FAT, but I like EXT2, install MUST be EXT2 for symlinks).
I'd also follow Jon_J's basic idea and put smaller stuff on flash and larger stuff on the MD.
I would avoid installing stuff to SD, as it is relatively slow.
----------------
In short/extra stuff:
Suggestions/DO:
-Use MRXVT 0.5.2 as your terminal instead of the default; it's fast, configurable, and has easy-to-use tabs.
-Try a different WM (Match/Open box is quite heavy IMO)
-Use swap on MD
-Have separate install and data partitions on MD
-Install big stuff to MD
DON'T DO:
-Install EVERYTHING to microdrive (slower than flash, eats battery)
-Install stuff to SD (slow)
NEED TO KNOW:
-It's ridiculously addictive...you'll probably spend more time using it than you'd like...like me.
Sorry for a messy post...
-
Well, I succesfully installed pdaXii (I fixed the NAND partition size limit, but forgot to change the size!), but now I'm getting an error when trying to start X.
Starting X
xauth: error in locking authority file /home/root/.Xauthority
xauth: error in locking authority file /home/root/.Xauthority
xauth: error in locking authority file /home/root/.Xauthority
xauth: error in locking authority file /home/root/.Xauthority
xauth: error in locking authority file /home/root/.Xauthority
Exiting X
I assume this has to do with pdaXii linking the hard drive and NAND, and my configuring it wrong?
-
Well, I succesfully installed pdaXii (I fixed the NAND partition size limit, but forgot to change the size!), but now I'm getting an error when trying to start X.
Starting X
xauth: error in locking authority file /home/root/.Xauthority
xauth: error in locking authority file /home/root/.Xauthority
xauth: error in locking authority file /home/root/.Xauthority
xauth: error in locking authority file /home/root/.Xauthority
xauth: error in locking authority file /home/root/.Xauthority
Exiting X
I assume this has to do with pdaXii linking the hard drive and NAND, and my configuring it wrong?
[div align=\"right\"][a href=\"index.php?act=findpost&pid=158527\"][{POST_SNAPBACK}][/a][/div]
Did you install pdaxrom beta 3 first?
If you forgot to change the size of the partition after using the "fix nand partition", go back and start over, do the fix nand and change it to 121MB, then reflash pdaxii13 (install rom)
-
Initially I couldn't finish the ROM install because I hadn't resized the NAND partition. So, while I searched the forums and retraced my steps vs the install guide I copied the hdimage over to save time. However, I'm thinking now it might be eaiser to simply start from scratch, wipe out everything and redo them in the proper order?
-
That's what I would do, start over and install pdaxrom and fix nand partition, then resize the nand to 121MB, install rom, and reboot. (I may have a step out of order, just follow the directions).
See if you can boot to the pdaxrom desktop.
If so, then install pdaxii13.
-
hI!
i run the pdaxii3 on the cacko by mounted images. I can honestly say it is slow but still awsome i can have ftp, gaim, at a descent speed. abiword is okay but i still would prefvfer more speed.
anyway, i recently installed the pdaxii3 meanie slapt together for the c1000 which installs into the internal flash. i highly recommend this. it is soooo fast and stable. i played with the operating system and it feels complete. it also works for the c3200 as stated in the html. it gives you an option to format the internal drive which is a big bonus especially if you want to restore to cacko or original rom. it has tools for restoring the z which i like. im going to take advantage of this in creating some themes for this as well.
when i installed, i used flash tools to uo the recommended size which is around 50 something and the rebooted and then installed rom and then formated user partition but not my internal drive just because i havent backed up my life. anyway, i bototed and all was fine. one thing was that i couldnt see my hdd3 or id3. most likely it needed mounting but i was very happy with the stability.
right now, using cacko thumb typing this while on bluetooth on cellphone being driven around.......sorry for my bad grammer
-
Well, I wiped out the hard drive, reinstalled the ROM, reinstalled the hdimage and everything is working fine now.
-
I'm not going to tell you to do this my way, but you can probably try a variation of my method.
On my C3200, I installed pdaxii13-akita on NAND
First you must install pdaxrom beta 3 to get pdaxii13 working, I think it needs the pdaxrom kernel from beta 3. (I don't know if this has changed recently, but when pdaxii13 first came out, it was only for the C3000, and users of other models needed to install pdaxrom beta 3 first)
http://www.users.on.net/~hluc/myZaurus/pdaxii13.html (http://www.users.on.net/~hluc/myZaurus/pdaxii13.html)
Once pdaxrom beta 3 is installed, you don't have to setup anything, just use the pdaxii13 files and reflash to pdaxii13
OK, this is the way I'm running pdaxii13-akita on NAND
What I did, was install small apps and utilities to flash, and I installed large apps, (like Firefox) onto the microdrive.
This gives me an OS and utilities that runs entirely from flash. This has a quicker response than installing everything to the hard drive.
[div align=\"right\"][a href=\"index.php?act=findpost&pid=158523\"][{POST_SNAPBACK}][/a][/div]
You do not need to install beta3 prior to installing pdaXii13 Akita. This was only a requirement for hacking pdaXii13 Spitz on a non C3000
-
DON'T DO:
-Install EVERYTHING to microdrive (slower than flash, eats battery)
-Install stuff to SD (slow)
Uhm ... I could not understand where to install everything?
P.P. I've about 300-400 mb currently installed to partition of HDD. Where I had to do this in your opinion?
-
EDIT: Editing config files at 2am leads to stupid questions.
-
Meanie I edited the PS1 value in /etc/profile, but your smiley face is quite presistant...where else do I need to change it?
[div align=\"right\"][a href=\"index.php?act=findpost&pid=158591\"][{POST_SNAPBACK}][/a][/div]
that's the only place it is defined. you need to source the profile ...
-
I was hoping nobody would notice this post so late! I got sidetracked doing something else after the edit and forgot to restart instead of just restarting X.
-
DON'T DO:
-Install EVERYTHING to microdrive (slower than flash, eats battery)
-Install stuff to SD (slow)
Uhm ... I could not understand where to install everything?
P.P. I've about 300-400 mb currently installed to partition of HDD. Where I had to do this in your opinion?
[div align=\"right\"][a href=\"index.php?act=findpost&pid=158568\"][{POST_SNAPBACK}][/a][/div]
The microdrive is good for big things, but I put the small stuff on flash so it loads faster. I also don't use a lot of large apps, so my view is skewed toward my needs.
-
Everything is working well now, I've got pdaXii installed and customized (largely removing redundant applications/ones I don't need and installing things I personally can't live without such as screen and less), but now torsmo isn't working. I've tried setting it to run automatically, and started it manually, but I just can't see it with -d. I know it's working, because I used the -o switch to check.
I've tried changing the background back to default, as well as setting no background at all.