OESF Portables Forum

Everything Else => Zaurus Distro Support and Discussion => Distros, Development, and Model Specific Forums => Archived Forums => Angstrom & OpenZaurus => Topic started by: steven999 on September 20, 2004, 06:53:30 pm

Title: OpenZaurus 3.5.1, 5600, USB, WinXP
Post by: steven999 on September 20, 2004, 06:53:30 pm

Hi All,

I'm new to OpenZaurus and Opie, previously been using Sharp 1.32 rom with overclocked Kernel on my 5600.  I installed OpenZaurus 3.5.1 today which runs very smoothly and looks great.  

However, after installing OpenZaurus, I can't seem to hit it anymore over USB.  Previously I was using Zaurus Manager to set to USB-TCP/IP setting so I could use FileZilla to transfer files, as well as use ssh from cygwin console.  Now I can not even ping it.  

I've tried changing the settings in Networking for usbd0 to use a fixed IP address of 192.168.129.201, subnet mask of 255.255.255.0, and gateway of 192.168.129.200.  This doesn't seem to do anything.  

Also, I tried using Qtopia Desktop 1.7 to sync with Zaurus but without luck.  QTDesktop doesn't seem to find the Zaurus.  

I'm really looking forward to getting things going with OpenZaurus; any help with these would be greatly appreciated!

Thanks,
Steven

Title: OpenZaurus 3.5.1, 5600, USB, WinXP
Post by: r0bin on September 20, 2004, 07:13:29 pm

Are you getting the error message: "Your connnection has limited or no connectivity" the popup yellow thing?

I just fixed it and can help you

Title: OpenZaurus 3.5.1, 5600, USB, WinXP
Post by: steven999 on September 21, 2004, 01:56:18 am

Hi r0bin,

I don't think it's the same issue as I'm not  getting any yellow popups.  Thanks for reply though, I'm going to give this another go tomorrow.

steven

Title: OpenZaurus 3.5.1, 5600, USB, WinXP
Post by: steven999 on September 21, 2004, 06:12:48 pm

Okay, it seems that the IP from the Zaurus Manager program is used.  If I manually put in an IP on the Network Connections in XP (Local Connection 3 for me), I can ping the Zaurus.  However, that's about all I can do.  I can't ftp, ssh, telnet, or anything.  I tried these settings:

Ethernet adapter Local Area Connection 3:

        Connection-specific DNS Suffix  . :
        IP Address. . . . . . . . . . . . : 192.168.129.201
        Subnet Mask . . . . . . . . . . . : 255.255.255.0
        Default Gateway . . . . . . . . . : 192.168.129.200

for both the network connection on WinXP as well as on the usbd0 setting on the Zaurus itself.  

If I ssh, I get:

ssh: connect to host 192.168.129.201 port 22: Connection refused

Dropbear seems to be running on my zaurus, and I have no firewalls enabled on my XP machine.  

I feel like I'm getting really close and I'm excited but frustrated at the same time.  If anyone can help out it'd be greatly appreciated.

Thanks,
steven

Title: OpenZaurus 3.5.1, 5600, USB, WinXP
Post by: lardman on September 21, 2004, 06:22:07 pm

Quote

Connection-specific DNS Suffix . :
IP Address. . . . . . . . . . . . : 192.168.129.201

and

Quote

ssh: connect to host 192.168.129.201 port 22: Connection refused

IP addresses must be different. Try 192.168.129.200 for the XP end of the connection; then use the ssh command as you used above.


Si

Title: OpenZaurus 3.5.1, 5600, USB, WinXP
Post by: steven999 on September 21, 2004, 06:36:36 pm

Hi Lardman,

That absolutely did the trick!  I'm now able to ssh and sftp into my Zaurus, which was what I did a lot of when I had the Sharp ROM on it.  Thanks very much to you for your help!

steven

Title: OpenZaurus 3.5.1, 5600, USB, WinXP
Post by: steven999 on September 21, 2004, 07:25:50 pm

...correction, I can ssh but no sftp.  sftp doesn't seem to be installed.