Messages

1

Zaurus - pdaXrom / XMMS problems

« on: July 13, 2004, 05:01:14 pm »

ps: what happens when you all try to run the equalizer on xmms? :->



It kills XMMS....   :-(


John Thomas

2

Zaurus - pdaXrom / XMMS problems

« on: July 12, 2004, 06:30:13 pm »

Thanks for the tip, works like a champ.

John Thomas

3

Zaurus - pdaXrom / XMMS problems

« on: July 12, 2004, 02:35:47 pm »

I have xmms and xmmsmplayer installed.
When I start playing a MP3, it plays for a second and then cuts out, plays again for a second and then cuts out again.  Any ideas as to what to look for?

John Thomas

4

Zaurus - pdaXrom / New pdaXrom installer (to have just Root partition)

« on: July 08, 2004, 04:56:02 am »

Is it possible to get the mtdtest.sh?

John

5

Zaurus - pdaXrom / pdaXrom and Senao 2511

« on: July 08, 2004, 02:57:39 am »

Laze, thanks for the patience. I messed up my Zaurus bad, and so I just reloaded pdaXrom so I could start fresh.

I then plugged the card in and ran cardctl ident-this told me the id information about the card

I then went to /etc/pcmcia/config.opts and added at the bottom

card "Senao 2511"
  version "WLAN", "11Mbps_PC-Card_3.0","ISL37100P","Eval-RevA"
  manfid 0x000b, 0x7100
  bind "orinoco_cs"

I think the issue was that I was pulling my CF card without doing a software eject.
If I run kismet and then stop kismet, it will do a ioctl error until I remove and reinsert the card.

Now, if I can figure out how to get it to work with the prism driver, I'll be all set  

John

6

Zaurus - pdaXrom / pdaXrom and Senao 2511

« on: July 04, 2004, 09:30:17 pm »

When I do the network start eth0, it says

ioctl():Device or resource busy

John

7

Zaurus - pdaXrom / pdaXrom and Senao 2511

« on: July 04, 2004, 04:17:42 am »

IWconfig

eth0      IEEE 802.11-DS  ESSID:""  Nickname:"zaurus"
          Mode:Ad-Hoc  Frequency:2.457GHz  Cell: 44:44:44:44:44:44  
          Bit Rate:11Mb/s   Tx-Power=15 dBm   Sensitivity:1/3  
          Retry min limit:8   RTS thr:off   Fragment thr:off
          Encryption key:off
          Power Management:off
          Link Quality:0  Signal level:0  Noise level:0
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0

xcardinfo
Socket 0  Senao 2511
state ready  CD  Vcc
device     eth0
IO ports  0xf6000000-0xf6000003  interrupt 39

ifconfig
lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0   TX bytes:0 (0.0

usbd0     Link encap:Ethernet  HWaddr 40:00:01:00:00:01  
          inet addr:192.168.255.40  Bcast:192.168.255.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:598 errors:0 dropped:0 overruns:0 frame:0
          TX packets:132 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:100
          RX bytes:86866 (84.8 Kb)  TX bytes:9652 (9.4 Kb)

8

Zaurus - pdaXrom / What is current version?

« on: July 01, 2004, 01:27:39 am »

When I reboot my SL-C860, the version shows as 1.0.0.

I downloaded and installed 1.0.5, do I have the wrong version, or is the displayed version wrong?


John

9

Zaurus - pdaXrom / pdaXrom and Senao 2511

« on: June 30, 2004, 01:31:55 am »

I found a stray character in the config file.
Now, it gets as far as

cardmgr[162]: + ioctl(): Device or resource busy


John

10

Zaurus - pdaXrom / pdaXrom and Senao 2511

« on: June 30, 2004, 12:41:32 am »

I have a new SL-C860, pdaXrom 1.0.5 and Senao NL-2511CF Mercury card.

cardctl status gives :-

"WLAN", "11Mbps_PC_Card_3.0", "ISL37100P", "Eval-RevA"
manfid: 0x000b, 0x7100
function: 6 (network)

i have tried adding this to the /etc/pcmcia/config, /etc/pcmcia/hermes.conf and /etc/pcmcia/wireless.conf files but with no results.

On other Topic, I have seen suggestions to use hostap_cs, orinoco_cs, prism2_cs,  and spectrum_cs for the binding. I have tried some of these and still cn't get it to work.

Thanks
John

11

Zaurus - pdaXrom / How to install pdaXrom?

« on: June 29, 2004, 01:52:15 pm »

Thanks. I ended up going in and uninstalling all the apps I installed. I then went through and deleted the IPks for those apps, and then was able to complete the install.

Thanks,
John