Messages

1

C1000/3x00 General discussions / Prboom For Zaurus

« on: December 23, 2004, 05:06:12 am »

I have installed the demodoom and it work fine.
However, when I put the other *.wad file in the corresponding folder, it cannot detect it.
I have serached many old posts and most of them just said put the *.wad file in the corresponding folder, then it will working fine.
Any tricks on this? Thanks.

- Ken

2

C1000/3x00 General discussions / Picsel Browser

« on: December 14, 2004, 08:28:29 pm »

I believe it is not come with the C3000.

- Ken

3

C1000/3x00 General discussions / Sl-c3000 Real Battery Time

« on: December 14, 2004, 08:04:27 pm »

I find that the battery indicator is not very clear. It can only show full and half.

Once it become half, it will suddenly prop up a message and said that need to connect to AC adaptor and then cannot power on.

Any better battery indicator program for C3000?

4

C1000/3x00 General discussions / How To Get Kismet Work With C3000?

« on: December 14, 2004, 07:59:07 pm »

Finally I make it work.
Please make sure the following in kismet.conf:

source=prism,wlan0,prism

I have tried source=prism_legacy,wlan0,prism but cannot success. After changed prism_legacy to prism, it is working.

5

C1000/3x00 General discussions / How To Get Kismet Work With C3000?

« on: December 10, 2004, 01:11:27 am »

I have tried the command line method before.

However, when I type "cardctl scheme CardResume",
it return "loctl(): Device or resource busy" problem.

But I am sure the Wireless CF is ok as I can connect to the wireless network normally.

- Ken

6

C1000/3x00 General discussions / How To Get Kismet Work With C3000?

« on: December 09, 2004, 05:15:18 am »

I have tried to use kismit with C3000 but cannot get it work.

When I run the kismit_server, it did not have any error message:

-----------------------------------------------------------------------------
Suid priv-dropping disabled.  This may not be secure.
No enable sources specified, all sources will be enabled.
Source 0 (prism2source): Using prism2 to capture packets.
Source 0 (prism2source):  Attempting to enter monitor mode.
Enabling monitor mode for a prism2 card on wlan0 channel 6
message=lnxreq_wlansniff
  enable=true
  channel=6
  prismheader=no_value
  wlanheader=no_value
  keepwepflags=no_value
  stripfcs=no_value
  packet_trunc=no_value
  resultcode=success
Source prism2source: Created child capture process 893
Capture child 893 (prism2source): Capturing packets from Prism/2 (DEPRECATED)
Enabling channel hopping.
Disabling channel splitting.
Allowing clients to fetch WEP keys.
WARNING:  Disabling GPS logging.
Logging networks to Kismet-Dec-09-2004-1.network
Logging networks in CSV format to Kismet-Dec-09-2004-1.csv
Logging networks in XML format to Kismet-Dec-09-2004-1.xml
Logging cryptographically weak packets to Kismet-Dec-09-2004-1.weak
Logging cisco product information to Kismet-Dec-09-2004-1.cisco
Logging data to Kismet-Dec-09-2004-1.dump
Writing data files to disk every 300 seconds.
Mangling encrypted and fuzzy data packets.
Reading AP manufacturer data and defaults from /usr/local/etc/ap_manuf
Reading client manufacturer data and defaults from /usr/local/etc/client_manuf
Dump file format: wiretap (local code) dump
Crypt file format: airsnort (weak packet) dump
Kismet 3.0.1 (Kismet)
Logging data networks CSV XML weak cisco
Listening on port 2501.
Allowing connections from 127.0.0.1/255.255.255.255
Registering builtin client/server protocols...
Registering requested alerts...
Registering builtin timer events...
Enabling packet source 0 (prism2source)...
Gathering packets...

--------------------------------------------------------------------------------------

However, it just stop at Generating packets without any response. I am sure it has wireless AP around here, as my friend's C860 can detect AP with the same config from me.

Anyone has idea?

- Ken

7

C1000/3x00 General discussions / Netfront 3.1 Did Not Support Yahoo Mail?

« on: December 07, 2004, 03:32:47 am »

I have tried to use the C3000 come with browser Netfront 3.1 but failed to login to Yahoo Mail. Anyone has solution?

Moreover, for the Opera 7.55, besides IBM website, anyone can provide the download? As IBM did not allow download from non-US countries.

- Ken

8

C1000/3x00 General discussions / Backup C3000 Microdrive?

« on: December 06, 2004, 10:16:33 am »

Any method to backup all the content of the C3000 Microdrive?

I understand the Jap Dictionary can be installed by the coming CD, how about the other software?

Thanks.

- Ken

9

C1000/3x00 General discussions / Could somebody teach me how to swap on C3000?

« on: December 06, 2004, 05:23:08 am »

Thanks. Andy.

I can check the swap status now.

However, I found that the speed of the application is running slower than before, is it normal?

And how can I revert back to original settings?

Sorry for so many questions.

- Ken

10

C1000/3x00 General discussions / Could somebody teach me how to swap on C3000?

« on: December 05, 2004, 10:44:17 am »

I am also a new C3000 user.
I have followed what Andy has taught, however, I cannot use "swapon -s" command to see the status of swap.

It only has swapon -a command in C3000.

Anyone has idea about how can I check the swap status? Thanks.

- Ken