Messages

1

5x00 Hardware / Sl-5500, 3.5.4, Netgear Ma701

« on: July 30, 2006, 11:16:22 pm »

Cardctl status?
[div align=\"right\"][a href=\"index.php?act=findpost&pid=136837\"][{POST_SNAPBACK}][/a][/div]

Socket 0:
   3.3V 16-bit PC Card
   function 0:  [ready]
Socket 1:
   no card


I have a 1gb SD card as well.

2

5x00 Hardware / Sl-5500, 3.5.4, Netgear Ma701

« on: July 28, 2006, 02:31:13 pm »

Is that what you're getting out of GPE/OZ, or out off dmesg?

If it's the former, run the Konsole, Pull it, Plug it, and list the last oh. . . say 20 lines from "dmesg" entered into the konsole.
[div align=\"right\"][a href=\"index.php?act=findpost&pid=136761\"][{POST_SNAPBACK}][/a][/div]

I didn't see anything in dmesg that really stood out for my card.

3

5x00 Hardware / Sl-5500, 3.5.4, Netgear Ma701

« on: July 28, 2006, 11:14:20 am »

I have an SL-5500 w/ OZ 3.5.4 running on it.  I am trying to get my Netgear MA701 to load but it won't.  When I insert the card it comes up as an unknown card, unknown manufacturer.  Has anyone experienced this before?  Any help would be awesome.

--Doug

4

5x00 General discussions / Netgear Ma701

« on: March 20, 2006, 02:41:51 pm »

Tried searching and could not find what I was looking for.

I have my 5500 flashed with 3.5.3 right now and plan on updating tonight.  I have never been able to get my Netgear MA701 working on this device.  Does anyone have some info on some setup instructions for this?

5

5x00 Hardware / Getting Openzaurus 3.5.3 On My Sl-5500

« on: October 11, 2005, 09:48:57 am »

Do you have alink to specifics on reloading the sharp rom.  I might have been doing that wrong(I am new to messing with embedded systems)  I am also going to go buy a new cf card tonight.  Just to be on the safeside.

6

5x00 Hardware / Getting Openzaurus 3.5.3 On My Sl-5500

« on: October 03, 2005, 01:57:07 pm »

it boots up for the first time with fs issues

What are these issues?

Si
[div align=\"right\"][a href=\"index.php?act=findpost&pid=97666\"][{POST_SNAPBACK}][/a][/div]

couldn't find ext2 superblock, trying backup blocks
The superblock could not be read or does not describe a correct ext2 filesystem
If the device is valid and it really contains an ext2 filesystem (and not a swap or ufs or something else), then the superblock is corrupt, and you might try running e2fsck with an alternate superblock.

This is after loading the ospack.

7

5x00 Hardware / Getting Openzaurus 3.5.3 On My Sl-5500

« on: September 29, 2005, 04:41:13 pm »

When I try to flash with the ospack it boots up for the first time with fs issues.  ANy help would be appreciated.  feel free to emai me at doug.arcidino@eastcoastlan.com.

8

5x00 Hardware / Getting Openzaurus 3.5.3 On My Sl-5500

« on: September 28, 2005, 01:46:00 am »

I hit the reset button just the directions said.  I think I need to pop the cf card into one of my nix boxes and make sure the card is fat16.

9

5x00 Hardware / Getting Openzaurus 3.5.3 On My Sl-5500

« on: September 27, 2005, 06:07:35 pm »

No the LED's come on for 3-5 mins.  It appears to be having an issue with booting.  I mean it flashes as far as  I can tell.

10

5x00 Hardware / Getting Openzaurus 3.5.3 On My Sl-5500

« on: September 27, 2005, 03:00:19 pm »

I have gone through the flshing process about 5 times and still when I boot up the zaurus it just sits at the sharp screen with the blinking cursor on the bottom right hand corner.  Any help would be awesome.