Messages

1

Software / Scummvm Problem

« on: February 23, 2006, 04:53:44 am »

Hi,
I start a new post, same topic, but have nothing to do with the hardware mentioned above. I have a SL-5500G with OZ3.5.3 installed.

Everything runs fine, browser, opie-reader,mplayer,xmms,etc., but now I want to install scummvm. I have tried the version from the feed, but it is claiming about libxext6 and libx11. Both libraries are installed. I force the installation but it doesn't run.

I tried the versions from http://www.gnurou.org/Code/SharpZaurus and http://chrisg.crispy-cow.de/zaurus/ but they doesn't run, too.

What version runs with my installation and what libraries must I install?? The libSDL from http://www.gnurou.org/Code/SharpZaurus is installed. libmad is installed, too.

I hope there are some people who are using scummvm on a SL-5500G. I want to play Sam&Max on my collie    .....so please help....

Thanks, Daniel

2

Angstrom & OpenZaurus / Ipkg And Segmentation Fault

« on: February 21, 2006, 03:59:13 pm »

I'm bit confusing now.... I installed konqueror-embedded with the machine feed activated, but there is no module anymore in the dep....

So, konqueror is installed and works fine......there was a dep break with libqte2 (my version is smaller than the required) but I force the installation and there it is. Konqueror in all his glory....

I don't know what was the solution, but now everything works.....   I'm so happy....

Thanks for all advices and thanks for that great piece of software (OE+Opie).......

Daniel

3

Angstrom & OpenZaurus / Ipkg And Segmentation Fault

« on: February 21, 2006, 07:16:21 am »

I only want to install xmms-embedded. As an dep there comes libstdc++. And if the machine feed is included the usb-serial modul. But if it isn't included everything installed fine.

Now, I'm using it without the machine feed....but to install KonquerorEmbedded, I need two libs from there, should I install it manually (download, and do an "ipkg bla") otherwise the usb-serial is going to install...

Or does anybody know a good browser on Zaurus?? Links to packages??

4

Angstrom & OpenZaurus / Ipkg And Segmentation Fault

« on: February 20, 2006, 04:22:04 am »

So, again....

I flashed my Collie and again, same errors. After installing the usbserial-module there is an segmentation fault if I use networking over USB. The usb-serial module will be automatically installed when I have the machine feed activate.

Now, I have flashed my Collie again, and I have not add the machine feed to ipkg.conf.
I need for KonquerorEmbedded, two libs from the machine feed, I think, I would download them manually and installed it manually, too.

The question is: Why installed ipkg the usb-serial modul by activating the machine feed?? And second: Why did this module "destroy" my USB netqorking from running??

Has anyone else these experiences?? Or don't use anybody USB networking??

Thanks, Daniel

5

Angstrom & OpenZaurus / Ipkg And Segmentation Fault

« on: February 17, 2006, 03:24:34 pm »

Now I'm at home.... I tested it with the -V flag..... I know that the "Segmentation fault" comes from the network device. No matter what I do with the network there comes a "Segmentation fault" even if I restart the network device.....I have configured it over the USB port and download the package over the docking station.

I remember that with the packages there comes a kernel modul for usb-serial. Why? I don't know. I think this isn't the right one for my kernel. I have the standard kernel from the original image installed. After some trying OPIE is not starting anymore. So I do a complete reflash of my Collie. It's not so bad, because I have it only for 3 days now, so there are not so important things on it.

But why installed ipkg a usb-serial modul if it isn't compatible??

I hope after the reflash there will be more luck in installing packages on it. I will report, if it is running....

6

Angstrom & OpenZaurus / Ipkg And Segmentation Fault

« on: February 17, 2006, 05:59:36 am »

Running out of ram is also a known cause for segfaults with ipkg
[div align=\"right\"][a href=\"index.php?act=findpost&pid=115142\"][{POST_SNAPBACK}][/a][/div]

After a reboot, the same error occurs....And finally after a reboot, there must be enough  RAM, I think....I have installed the zImage-collie-64-0, so I think I have enough RAM.....

I will try -V flag as soon as I'm at home. At the moment I'm at work.

Daniel

7

Angstrom & OpenZaurus / Ipkg And Segmentation Fault

« on: February 17, 2006, 03:49:21 am »

Hi,

I have a problem with ipkg. I installed several programs on my SL-5500, such as opie-reader, qpdf2, mplayer, opie-player. The installation of these programs were without problems. I installed it on the SD-Card, I formatted it before with ext2 for making symlinks. After the installation I run ipkg-link with mount /path/to/packages. Every program runs fine, no problem. But if I will install new packages, ipkg download the package and then "Segmentation fault". That's it. I know what a "Segmentation fault" is, but why does it appear. I have included the rights feed from the Ewi mirror.

Deinstallation of programs runs, there is enough space on my SD.

Have anyone a suggestion??

Thanks, Daniel

Hardware: Sl-5500 (Collie)
Software: OZ3.5.3/Opie1.2.0