Messages

1

SIMpad forum / Can't Access The Bl Monitor Menu

« on: April 04, 2006, 02:04:28 am »

Problem solved!

I got tired to wait so I skipped the "erase flash section" and jumped right to serload blupdater.img instead.
It went fine so I followed the rest of the instructions to install Opie 0.9-rc1, and now it's
running fine!

I have some problems but I will start a new thread about that..
Thanks for the help anyway..

2

SIMpad forum / Can't Access The Bl Monitor Menu

« on: April 02, 2006, 05:57:25 pm »

Is there anyone who can post the exact settings for hyperterminal you've used
sucessfully? I don't mean 38400 8N1 but the other settings.

3

SIMpad forum / Can't Access The Bl Monitor Menu

« on: April 02, 2006, 05:12:38 pm »

Update:

I fiddled around in HT a bit and finally succeded in accessing the monitor menu!
I had wrong setting in "terminal type"..

But unfortunately I'm suck in the menu now..
When I press "y" for "erase flash" absolutely nothing happens.. gaaaahh!
Guess I'm not supposed to hav Linux on my SIMPad

4

SIMpad forum / Can't Access The Bl Monitor Menu

« on: April 02, 2006, 04:44:21 pm »

I assume that you have been pressing the escape key on the serial terminal's keyboard - this should work.

Another way to get the menu to appear, is to reset your Simpad whilst at the same time holding down the lower Simpad front-panel key (the key that brings up the on-screen keypad in WinCE). Just successfully tested this with the 2.5.3 bootloader.

Ralph
[div align=\"right\"][a href=\"index.php?act=findpost&pid=121491\"][{POST_SNAPBACK}][/a][/div]

Tried this.. no luck
It just keeps on booting as if I never pressed ESC.

I wonder if it can be some wrong settings in hyperterminal?
Which terminal type should it emulate? VT100, ANSI or something else?
I'm using swedish keyboard, does this affect hyperterminal in any way?
Is there any other settings in HT I can change? I'm out of ideas.

5

SIMpad forum / Can't Access The Bl Monitor Menu

« on: April 02, 2006, 03:20:27 pm »

Did you press it all the time? If not try the following:
- press esc, keep pressed
- press the reset button while keeping esc pressed
- keep esc pressed ;-)

I've tried every possible combination.. pressing ESC a moment before reset,
pressing ESC at the same time as reset, pressing ESC a moment after reset,.. and so on.. no luck so far..

have you verified that you can send data from the pc to the pad via serial with some program?

I have successfully upgraded the bootloader from 2.4.20 to 2.5.3 following
the instructions I've found on this forum.
So the cable seems to work ok.

I have no clue what so ever what to try next...

6

SIMpad forum / Can't Access The Bl Monitor Menu

« on: April 01, 2006, 04:12:24 am »

Hi.
I've recenly bought a Simpad SL4.
I want to switch the originally installed CE 3.0 for Opie or Gpe.
After some reading in this forum and opensimpad.org, I
got started.

So far I've managed to:

1. solder a simple serial cable (gnd, rx, tx).
2. serloaded bl_loader.alt, reset
3. serloaded bl_loader, reset

Everything went as expected so far.
BL was upgraded from 2.4.20 to 2.5.3, so far so good.
Next step should be to boot and access BL monitor menu to erase flash, right?
Here comes the problem.
I can't get the simpad to react pressing the ESC key. It just boots as
normal whatever I do.

Terminal settings are 38400 8N1.
I've tried it on 2 computers, with HT and MiniCom, no luck.

Is IS possible to do this even with a "simple" serial cable, right?
Or am I missing something?

Help!

Sorry for my not so good english, hope you understand.