Topics

1

Zaurus - pdaXrom / Can I Set A Latency On The Power On Buttons.....

« on: December 01, 2006, 11:06:21 am »

Hello, i have a problem, when i put my Z in the bag, the Z power on because something for error push the power on button.......

Can i set that the Z start only when i press the power button and hold it for 5 seconds ?

THANKS

Bye

2

OpenBSD / How To Install Openbsd On C1000 ?

« on: October 18, 2006, 09:40:00 am »

Hello, i have a sharp rom on my C1000, i have one card SD 1gb Kingston and a CF card Wi-fi XI-825.

How can i install openBSD ?
Wich are the file ?

What i must do ?

THANKS

Bye  

3

Cxx0 Hardware / Nand Flash Memory -> Bad Block Num=4

« on: October 12, 2006, 08:42:34 am »

I was tring to install various ROM and none works right.....

Cacko    https://www.oesf.org/forums/index.php?showtopic=21601&hl=
Beta 3    https://www.oesf.org/forums/index.php?showtopic=21089&hl=

only pdaxrom beta4 works, so i try to make:

 Extra MENU -->
 Zaurus Test -->
 NAND Flash (Full) -->

The result is:

Bad Block Num = 4

Can do this the problem ?

What can i do ?

THANKS

Bye

4

Zaurus - pdaXrom / [urgent] On My Pdaxrom Don't Work Touchscreen..

« on: October 10, 2006, 08:41:16 am »

For error i install the tslib from the feed... now when i touch the screen it's not work....and the X work at the max.....

I try to reclibrate...but when i launch ts_calibrate, the Z say :

Code: [Select]

xres = 480, yres = 640
ts_read:invalid argument
What can i do ?

THANKS

Bye

5

Zaurus - pdaXrom / Gaim Don't Work With Msn

« on: October 10, 2006, 05:28:47 am »

When i try to use Gaim with my account MSN, it say:

" ....... SSL support is needed for MSN. Please install supported SSL library........"

What can i do ? Do I must install some packages ? Wich ?

THANKS

Bye

6

Sharp ROMs / Problem To Install Cacko

« on: September 29, 2006, 08:19:16 am »

Hello, I was using pdaxrom, but now i want to try cacko.

Trought my SD i have made NAND Restore for re-install the Sharp boot loader and the Sharp ROM. It's OK and the Sharp ROM works fine but in JP.
I download this file http://cacko.oesf.org/downloads/rom/1.23/S...-1029311005.zip
I unzip it and put the file on the root of SD, when Z  reboot press ok and make partitioning and install new rom. The installation is ok. Reboot.

When Z start, it remaining with the Sharp logo and make nothing....        

What can i do ?

Anyone have a NAND Backup with Cacko Installed ?

THANKS

Bye

7

Sharp ROMs / Wich Are The Difference Between Sharp & Cacko Rom?

« on: September 27, 2006, 10:19:22 am »

Which are the difference between sharp rom and Cacko Rom??

The desktop enviroment is equal ?

What's change?          

THANKS

Bye

8

Zaurus - pdaXrom / How Can I Make A Full Backup ?

« on: September 26, 2006, 04:35:59 am »

Hello i'ld want to try other distro, but i don't want to lose the settings and customization that have made to my installation.....

How can i do ? Because the mtdblock5 is mounted!

THANKS A LOT

Bye

9

Zaurus - pdaXrom / [u-boot] How I Can Install Beta3 Or Cacko ?

« on: September 25, 2006, 10:36:05 am »

I have installed pdaXrom beta4 with u-boot ...... now i want try other distro.....

Can i install this other distro trought the u-boot ?

The distro is :

beta 3
cacko
OZ

How can i do ?

THANKS

Bye

10

Zaurus - pdaXrom / Usb To Lan Don't Work!

« on: September 22, 2006, 08:52:34 am »

The gadget is this :
http://cgi.ebay.it/ws/eBayISAPI.dll?ViewIt...AMEWN%3AIT&rd=1
is an ST268 USB NIC, when i use it on pdaXrom it's not work!

What can i do ?

Code: [Select]

root@zaurus ~# lsusb -v

Bus 001 Device 014: ID 0a46:0268 Davicom Semiconductor, Inc.
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               1.10
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0         8
  idVendor           0x0a46 Davicom Semiconductor, Inc.
  idProduct          0x0268
  bcdDevice            1.01
  iManufacturer           1 ShanTou
  iProduct                2 ST268 USB NIC
  iSerial                 3 0268
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           39
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xa0
      Remote Wakeup
    MaxPower              144mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           3
      bInterfaceClass         0 (Defined at Interface level)
      bInterfaceSubClass      0
      bInterfaceProtocol      0
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               none
          Usage Type               Data
        wMaxPacketSize     0x0040  bytes 64 once
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x02  EP 2 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               none
          Usage Type               Data
        wMaxPacketSize     0x0040  bytes 64 once
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x83  EP 3 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               none
          Usage Type               Data
        wMaxPacketSize     0x0008  bytes 8 once
        bInterval               1
  Language IDs: (length=4)
     0409 English(US)
THANKS              

Bye

11

Zaurus - pdaXrom / Minicom Incompatible With Aterm

« on: August 29, 2006, 08:44:47 am »

Hello, i've installed minicom from feed .

When i open my default console aterm and start minicom, minicom start but don't work the CTRL-A Z key, every button press the minicom do nothing.

If i use mrxvt it's work right.

What can i do ?

THANKS

Bye

12

Zaurus - pdaXrom / Usb To Serial Converter Don't Work

« on: August 29, 2006, 08:00:45 am »

Hello, i was try my USB  to Serial converter.

The Z see it right and load the right module, it say that is attached in ttyUSB0, but in /dev thereisn't this mount point.

Code: [Select]


usb 1-2: new full speed USB device using pxa27x-ohci and address 2
usb 1-2: configuration #1 chosen from 1 choice
usbcore: registered new driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
usbcore: registered new driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver core
drivers/usb/serial/usb-serial.c: USB Serial support registered for pl2303
pl2303 1-2:1.0: pl2303 converter detected
usb 1-2: pl2303 converter now attached to ttyUSB0
usbcore: registered new driver pl2303
drivers/usb/serial/pl2303.c: Prolific PL2303 USB to serial adaptor driver
What can i do ?

THANKS

Bye

13

Zaurus - pdaXrom / Snes9x Package For Pdaxrom

« on: August 29, 2006, 05:38:27 am »

Hello, i want install a snes9x emulator, but i don't find the package.

Can you help me ?

THANKS

Bye

14

Linux Applications / How To Link The Depends ?

« on: August 25, 2006, 12:07:33 pm »

Hello, i tried to compile one package, like say this how-to ( https://www.oesf.org/index.php?title=Pdaxro...oss_Compilation ), the package is  "directvnc" but this package depend by the  "DirectFB" .

I have compiled the DirectFB right and i created the install dir ipkg-temp.

Now when i compile the directvnc package, how can i say at the compiler that the DirectFB package is in /root/DirectFB/ipkg-temp ?          
 
THANKS      

Bye

15

Zaurus - pdaXrom / C1000 With Beta4, Wich Mplayer I Must Install ?

« on: August 23, 2006, 10:08:24 am »

In the forum there is this new package https://www.oesf.org/forums/index.php?showtopic=20241

but it's work right on my beta4 ?

Wich package i must install ?

THANKS

Bye