Messages

16

Accessories / Cf Card

« on: May 04, 2007, 11:08:07 am »

Hi sdjf: Somethings more: The modem car( Targus ) is for receiving mails from a fone line , the WiFi card (D-link Air, DCF 660 W,Wireless Compact Flash 802.11b) is for connecting to the web in places where are wifi signal, them I need to know the Wep key in the networking configuration. I have used the two ones without problems.
And now the most foolish thing: I observed that the new CF data card 1Gb about we are speaking, appears ( I don´t remember if I said to you) in the collie as

Code: [Select]

card 0/pmcia: ATA/IDE  Fixed Disk)[/color]  the pmcia is a card por notebooks. So I decided with the collie off change the new for the older CF card, put the collie on and the machine begins to function normally, of course without the new books and other things I that charged in tis mid time. Them I try to eject the card via applet, and was ejected without problem!, them I entered the new card that was recgnized as card 0:  ATA/IDE Fixe4d Disk, That is the

Code: [Select]

pmcia not appearing[/color]and begin to use it normally, everything were there and made the test of eject it many times. I don´t no why....may you understand?...
Thankyou for you help, and wait for anything you want to say me.
My best regards
baptista

17

Accessories / Cf Card

« on: May 02, 2007, 03:55:07 pm »

Hi sdj: Ok it is also many things for me..but in April 30 you said:

"Another thing to do is run "ps ax | more" to get a full list of everything that is running. Do you see anything that might be holding on to the card? If you are not sure, then paste the output here."

Stageone is a program type iqnotes, kapi and kopi are programs for pim data,installed on SF card so I have it duplicated, and are more efficient than the zaurus one,( zautrix) is the name of the developper.

With the file manager open I can´t eject the card.

sdj, excuse me, but in all this time i´m speaking about CF data card. Everything began when you said that Type I or II is a matter of thickness, and really I could copy all the data of the ancient card type II with 500Mb to this one that we are speaking of 1GB. My ROM is 3.13
I´ll hope that you will not worry with me....and many thanks for everythings that I´m learning.

My best regards
baptista

18

Accessories / Cf Card

« on: May 02, 2007, 11:53:22 am »

Hi sdjf, here goes the answer of the console to the command you said:


  PID TTY      STAT   TIME COMMAND
    1 ?        S      0:03 init
    2 ?        SW     0:04 [keventd]
    3 ?        DW     0:00 [swapper]
    4 ?        DW     0:00 [swapper]
    5 ?        SW     0:00 [swapper]
    6 ?        SW    73:42 [kapm-idled]    7 ?        SWN    0:00 [ksoftirqd_CPU0]
    8 ?        SW     5:04 [kswapd]
    9 ?        SW     0:00 [bdflush]
   10 ?        SW     0:25 [kupdated]
   11 ?        DW     0:00 [swapper]
   12 ?        SW     0:29 [mtdblockd]    96 ?        S      0:00 /sbin/sdmgr   130 ?        S      0:06 /sbin/cardmgr
  149 ?        S      0:00 /usr/sbin/inetd
  159 ?        S      0:00 /usr/sbin/rpc.portmap
  169 ?        S      0:00 /home/QtPalmtop/bin/atd /var/spool/at
  206 ?        S      0:48 /usr/local/bin/tssimd
  208 ?        S      0:54 /sbin/shsync  367 ?        SN     0:00 /usr/local/bin/fbvncserver -double -rfbauth /home/zau
  437 ?        S      0:00 /sbin/launch  438 ?        S      0:00 /bin/sh ./qpe.sh
 1188 ?        SN     1:25 qpe -owner zaurus.qpe
 1189 ?        SN     0:00 qeserver zaurus qpe
 1191 ?        SN     0:02 qeserver zaurus qpe
 1220 ?        SN     0:00 addressbook -qcop /tmp/qcop-msg-addressbook
 1221 ?        SN     0:00 todolist -qcop /tmp/qcop-msg-todolist
 1222 ?        SN     0:00 qtmail -qcop /tmp/qcop-msg-qtmail
 1223 ?        SN     1:51 stageone -qcop /tmp/qcop-msg-stageone
 1224 ?        SN     0:55 kopi -qcop /tmp/qcop-msg-kopi
 1225 ?        SN     0:26 kapi -qcop /tmp/qcop-msg-kapi
 1226 ?        SN     0:00 datebook -qcop /tmp/qcop-msg-datebook
 1229 ?        SN     0:50 launcher -qcop /tmp/qcop-msg-launcher
 1230 ?        SN     0:07 qeserver zaurus qpe
 1231 ?        SN     0:06 qeserver zaurus qpe
 1232 ?        SN     0:05 qeserver zaurus qpe
 1233 ?        SN     0:57 qeserver zaurus qpe
 1718 ?        SN     0:02 embeddedkonsole -qcop /tmp/qcop-msg-embeddedkonsole 1719 ttya0    SN     0:00 /bin/bash
 1720 ttya0    RN     0:00 ps ax
 1721 ttya0    SN     0:00 more

When I try to eject the CF card with thw collie on the response is:
(Eject card 0: ATA/IDE FixedDisk) :
CF/PMCIA ejct failed
(Ejecting SD-card):
Failed to eject the card. Please eject the card after you close all applications and turn off the Zaurus.
In fact I have installed KOPI/KAPI in the SD but also in the file browser appear files of it in the /home/zaurus.
Why would not be the samething for ejecting CF card?

Excuse me if i spoke many things wrong.... Well now I wait your evr kind response, and would like to have some explication abou all this, if you have patience.
Greatfully
baptista

19

Accessories / Cf Card

« on: May 01, 2007, 04:31:48 pm »

Thankyou very much sdjf for your interest in help me, I have in the card some programs, a lot of books in pdf, gzip and hamcomword. Many musics and some films(clips).
The command about qcop functions, the clock appear!
The first command you send to me answer a lot of things that if I have time enough, i´ll send to you today or tomorrow, I think that some of them make reference to the card but I´m not sure now.
Now we (I..) are very near of a solution.
It happens the same thing with the SD card, that has 256 MB (SD), but it is not so necessary to eject,  because the CF card I need to eject it to put a modem card or a WiFi card.
Regards from
baptista

20

Accessories / Cf Card

« on: April 15, 2007, 01:39:42 pm »

Thanks to everybody that try to help me. At last I meet  the way. I suspend the collie, push out the CF card II copy it to CF card type I via a memory reader writer and insert CF type I to the machine, that all. The only thing is  that this type of card is not detected by the applet, so it is not necessary to eject it (I think so...). Nevertheles everything is functioning OK.
baptista

21

Accessories / Cf Card

« on: April 12, 2007, 04:55:37 pm »

I´m saying that I umount it from terminal and them would be possivel to eject it via aplet. Is it correct? Thanks for the help
baptista

22

Accessories / Cf Card

« on: April 12, 2007, 11:18:42 am »

Thankyou for the help Capn_Fish, but I can´t eject the CF via applet or terminal: umount /mnt/cf, what is wrong?. Excuse me the little aknowlegment, thanks again.
baptista

23

Accessories / Cf Card

« on: April 09, 2007, 11:52:20 am »

Hi people: I´m working with my collie with a 500Mb card type II. Now for a mistake I received a card type I with 1 GB. Any problem to read the data and transfer it for ancient to new card?.
Thanks for any help
baptista

24

5x00 General discussions / Backuping Up The 5500

« on: September 11, 2006, 02:09:26 pm »

Hi people: Thankyou very much to all, as ever I had a great help!, excuse me the time passed in answer.
baptista

25

Software / Kdepimpi 2.2.5

« on: August 04, 2006, 05:28:59 pm »

Hi, bluedevils, here I am but with good news now. Yesterday I made one new download from other mirror, Seattle, Washington,I think now that others downloads were corrupted, as you said in one mail,  and must be the proximity of Bush... but the fact is that I could install all de packages in the SD card, after that I downloaded my calendar.ics that was in the collie, and need to correct some minor things. Now I unsdertood the Kopi symbol in the taskbar, it is very good.
The only thing that don't go is the OM/Pi, it explodes but nothing open, I don't use it for now but perhaps you will have some tip for it.
As ever I'm very gratefull to you by your kindly help.
Thanks again from
baptista

26

Software / Kdepimpi 2.2.5

« on: July 28, 2006, 01:21:22 pm »

Hi Bluedevil, thanks again for your help, but the things does'nt go yet. The terminal don't know the command unzip, it know the gunzip. So I open the file out as a zipfile and install again everything, I could install opiemail,password and adressbook, Kopi give the same problem as I said in the begining. Nevertheless the programs installed din'nt operate, strangely it appears a simbol of Kopi in the task bar opening only the alarms...
I see by the filemanager that something is not correct, but I'm afraid to move in it. I think that is necessary to download many times the files becouse the possibilities of corruption is great.
As this week I'm travelling till the next friday will make the operation at my return,if it is possible I wait don't bore you many times...
Warm regards
baptista

27

Software / Kdepimpi 2.2.5

« on: July 26, 2006, 04:47:06 pm »

Hi bluedevil. I deleted everything in the SD card. I download the targz  file from the sourceforge and from the terminal I did the commands you said i.e.
gunzip <targz Kdepimpi-2.2.5> the answer was
Syntax error near unexpected token "<Kdepimpi-2.2.5>"
Well I saw your new advertences and will do a little later.
For everythings thanks again
baptista

28

Software / Kdepimpi 2.2.5

« on: July 26, 2006, 03:14:05 pm »

Thankyou very much bluedevils, I see that you are ever helping others in this foruns.
Really the files were zipped, but I extracted it and install, everything ok the first time I done, theproblem was after, as I related.
I asked for install from the terminal as a solution, and I'll try today, the matter is if from the terminal the files goes to the SD card. I don't made nothing with the SD card but I see by the documents some rests of ancient instalation there. I'll be in contact. Thanks again !

29

Software / Kdepimpi 2.2.5

« on: July 25, 2006, 03:50:19 pm »

I have being working usually with this new stable version 2.2.5, that I liked very much. But I certainly had a bad sync or something so, and the the icons of Kapi or Kopi never more worked.
Then I unistalled the program, that was in SD card and try to reinstall. Ever I obtained the same answer when I try to install in the SD:
 The extract of some files are failed. This application may not execute normaly. When you cannot operate this application please remove it, and the advise OK,
Pressing the button the answer: This application is available only for main memory. Please install it in the main memory.... What to do?. I reload many times the archives ipk and the same thing.. How I can install from the Terminal the targz package, what is the command?
Any help people? Thanks very much. I can´t return to the ancient Pim...

30

5x00 General discussions / Backuping Up The 5500

« on: July 14, 2006, 05:04:57 pm »

Hi. May I backup the 5500 with the program included in the v. 3.13 ROM that appears to be made for the 5600? It make the back in the desktop, and appears to be interesting. Any help? Thanks
baptista