Messages

1

C1000/3x00 Hardware / C1000 - Hw Pb With Touch Screen

« on: March 08, 2010, 05:45:57 am »

From the command line, remove /etc/pointercal and run startx again.
or ts_calibrate should do the trick.

Late

Hi  InSearchOf,

Under PdaXRom, I've allready remove /etc/pointercal  and run startx again : the display stay "off-line".

The screen is rougly working in DEBUG-MODE but not with an OS ...?

Thanks.

2

C1000/3x00 Hardware / C1000 - Hw Pb With Touch Screen

« on: March 07, 2010, 12:58:00 pm »

Hi Jon_J,

I've tried to install a Cacko, but you must "Tap" on the screen => No results.
I've also try with a PdaXrom, same result

If you have Cacko loaded try to recalibrate the screen.
Navigate using the keyboard to the "Settings" screen. (Use the "Home" key to switch tabs to "Settings").
Next, using the arrow pad, navigate to "Recalibrate". It is self explanatory, as I just did it on my C3100.

Thanks for your reply

3

C1000/3x00 Hardware / C1000 - Hw Pb With Touch Screen

« on: February 28, 2010, 10:30:04 am »

Hello,
I've some troublshooting with my C1000. When I use the point to press in the screen, the action isn't recognized.

In "DEBUG MODE", there is  3 pages and in the page 3, the choice 7, there is "7. Extra Menu".
In "Extra menu" -> "1 Zaurus Test" -> "7. H Display". This option presents the character "H" or "h" on all the screen. When a place is touched, the screen commute between "H" and "h". This test is OK.

But, under Cacko, PdaXrom, the action isn't recognized. Isn't possible to make a new sceen's setup, where you press in the 4 coins of the screen.

Could you help me, to solve my problem ? A zaurus without touchscreen is too sad

Thanks a lot.

Randy

4

Zaurus - pdaXrom / Build Pdaxrom, Cross-compile : Some Evolution ? (don't Shout Me Please)

« on: February 23, 2009, 03:08:32 am »

Thanks for the link and  your advice.

5

Zaurus - pdaXrom / Build Pdaxrom, Cross-compile : Some Evolution ? (don't Shout Me Please)

« on: February 22, 2009, 11:33:46 am »

Hi,
Fisrt, I must give some explications. I 'd looked at the www.pdaxrom.rom for several months without see anything chanching. And I'm using the Cacko to synchronise Outlook with the Zaurus for a while. I've forgotten to watch the forum ... sorry.

Now, I would come back to PdaXrom and use the cross-compilation. My second aim is to prepare an environment for this event : Solution Linux (Paris).

I'd looked at : PdaXrom Development, OESF Wiki Cross-Compilation and Beginner's Cross Compile Question.


My question is : What's the BEST way to build the environment ?

I'm waiting yours advices.


Thanks.

6

Zaurus - pdaXrom / Missing Or Can't Find Libiconv.so.2

« on: April 04, 2008, 09:02:36 am »

Thanks you, Jon_J, for the files .  I've not this files on my Beta3.

THANKS !

7

Zaurus - pdaXrom / Problem With Inodes At The Boot Time. [solved]

« on: September 21, 2006, 03:15:01 am »

1) Yes, there is no problem with the hardware
2) Just to clarify, what you posted above didn't show any errors at all - it was just letting you know that everything it planned to do is now done

(although tune2fs gave an error because it's built for ext2 and you tried to use it on jffs2)
[div align=\"right\"][a href=\"index.php?act=findpost&pid=141897\"][{POST_SNAPBACK}][/a][/div]

Hourra ! Thanks everybody for your help.

Have a good day.

Randy11

8

Zaurus - pdaXrom / Problem With Inodes At The Boot Time. [solved]

« on: September 20, 2006, 03:21:11 am »

Sorry, disregard that comment - as pelrun said above, there is nothing wrong. The filesystem leaves all that stuff to clean up later to save too many writes to memory.
[div align=\"right\"][a href=\"index.php?act=findpost&pid=141814\"][{POST_SNAPBACK}][/a][/div]

Thanks, for the replies. Well, if my understanding is good:
- no problem with the hardware;
- nothing will be done by the system, except if there is too many errors.

I'm right or not ?

For the fun, I will suppose that the corrections could be done :
- make a backup of the faulting partition on a true ext2 partition;
- make the corrections : "wrong magic", ...
- build an image for the jffs2 filesystem;
- replace the faulting file (jffs2 image) with the new.

(At this time it's not necessary in my particular case.)

What do you think about this idea ?

9

Zaurus - pdaXrom / Problem With Inodes At The Boot Time. [solved]

« on: September 19, 2006, 03:49:34 am »

Are these correctly unmounted at shutdown (especially the second one)?
[div align=\"right\"][a href=\"index.php?act=findpost&pid=141743\"][{POST_SNAPBACK}][/a][/div]

No   , a HARD RESET was done... But I've the same message without the CF (/dev/hd2) or SD (/dev/mmcda1).

10

Zaurus - pdaXrom / Problem With Inodes At The Boot Time. [solved]

« on: September 18, 2006, 10:42:38 am »

Hello,

I'm running a Beta3 on a SL-C1000. At the boot time I have

Cramfs: wrong magic
FAT: bogus logical sector size 381
Inode #1666 was a directory with children - removong those too...
Inode #2442 was a directory with children - removong those too...
Inode #2464 was a directory with children - removong those too...
Inode #2468 was a directory with children - removong those too...
Inode #11343 was a directory with children - removong those too...

If there is no CF or SD, it's the same thing.
The NAND is good : Menu Service (D+M).
I've tried

# tune2fs -c 2 -C 3 /dev/mtdblock3
tune2fs 1.34 (25-Jul-2003)
tune2fs: Bad magic number in super-block while trying to open /dev/mtdblock3
Couldn't find valid filesystem superblock.
#

When I make a "mount" :

rootfs on / type rootfs (rw)
/dev/root on / type jffs2 (rw)
/proc on /proc type proc (rw)
none on /dev type tmpfs (rw)
/dev/mtdblock3 on /home type jffs2 (rw,noatime)
none on /dev/pts type devpts (rw)
/dev/mtdblock3 on /mnt/user type jffs2 (rw,noatime)
/dev/mmcda1 on /mnt/card type ext2 (rw)
/dev/hda1 on /mnt/cf type vfat (rw,noatime)
/dev/hda2 on /mnt/cf2 type ext2 (rw,nosuid,nodev)

I've also tried a Backup/Restore (D+M) : no modification. The backup reproduce the problem (the filesystem keep the bug)  : it's a  normal situation because de NAND has no default, only the filesystem.

How to obtain a normal filesystem ?

Thanks for your help.

Randy11

11

Zaurus - pdaXrom / C3100 - Freeze After Long Suspend

« on: April 27, 2006, 05:29:27 am »

Hi,

Sorry, I've  looked the file, but I don't see what are the lines to modify ... Could you tell me which ones we need to modify?

Randy11.

Edit /etc/xdg/openbox/rc.xml

All the key-mappings are in there for matchbox.
 - Bundabrg
[div align=\"right\"][a href=\"index.php?act=findpost&pid=107160\"][{POST_SNAPBACK}][/a][/div]