OESF Portables Forum > All posts by a member| Posted on: Nov 2 2008, 07:00 AM | |
|
Group: Members Posts: 4 Joined: 16-September 07 Member No.: 20,407 
|
QUOTE(utx @ Nov 2 2008, 03:02 PM)  Please try netmask 255.255.255.0. I am surprised, that netmask 255.255.255.255 from my example was ever working. Thx for helping me, i changed the netmask to 255.255.255.0, but it didnt work  Which version of angstrom are you using? |
| Forum: Angstrom & OpenZaurus · Post Preview: #180298 · Replies: 6 · Views: 8,088 |
| Posted on: Nov 2 2008, 05:02 AM | |
|
Group: Members Posts: 4 Joined: 16-September 07 Member No.: 20,407
|
QUOTE(utx @ Nov 1 2008, 10:09 PM) You have bad configuration. You are configuring ifconfig with a different network address than route (101 x 201). Here are my files: Manual setup ifcfg-usb0 for automatic setup in openSUSE Thanks for your reply, I tried your script, but usb networking is still not possible for me  Now my config looks like that: desktop: ifconfig: CODE eth5 Link encap:Ethernet HWaddr 00:90:27:54:0E:D5 inet addr:192.168.1.10 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::290:27ff:fe54:ed5/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:30073 errors:0 dropped:0 overruns:0 frame:0 TX packets:26165 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:30927764 (29.4 MiB) TX bytes:2415453 (2.3 MiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:589 errors:0 dropped:0 overruns:0 frame:0 TX packets:589 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:61128 (59.6 KiB) TX bytes:61128 (59.6 KiB) usb0 Link encap:Ethernet HWaddr DE:3A:E8:4A:93:2C inet addr:192.168.129.1 Bcast:192.168.129.255 Mask:255.255.255.255 inet6 addr: fe80::dc3a:e8ff:fe4a:932c/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:96176 dropped:0 overruns:0 frame:0 TX packets:6 errors:501 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0  TX bytes:468 (468.0 route - n: CODE Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.129.201 0.0.0.0 255.255.255.255 UH 0 0 0 usb0 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth5 0.0.0.0 192.168.1.252 0.0.0.0 UG 0 0 0 eth5 zaurus: ifconfig: CODE lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1739 errors:0 dropped:0 overruns:0 frame:0 TX packets:1739 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:191760 (187.2 KiB) TX bytes: 191760 (187.2 KiB) usb0 Link encap:Ethernet HWaddr 6A:67:78:C5:07:1B inet addr:192.168.129.201 Bcast:192.168.129.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:30 errors:0 dropped:0 overruns:0 frame:0 TX packets:24 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1906 (1.8 KiB) TX bytes:756 (756.0 route - n: CODE Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.129.1 0.0.0.0 255.255.255.255 UH 0 0 0 usb0 0.0.0.0 192.168.129.1 255.255.255.255 UG 0 0 0 usb0 i hope you can help me, that would be great |
| Forum: Angstrom & OpenZaurus · Post Preview: #180296 · Replies: 6 · Views: 8,088 |
| Posted on: Nov 1 2008, 11:25 AM | |
|
Group: Members Posts: 4 Joined: 16-September 07 Member No.: 20,407
|
Hello all, at the moment I m trying to get USB networking configured for the Zaurus CL1000. The Zaurus is running Angstrom x11-image 2007.12-r18. Basically I tried to get it working by performing the steps which are described in the USB networking howto on the Angstrom wiki (http://linuxtogo.org/gowiki/AngstromManual)... Nevertheless its not working for me  I did following on the zaurus:
Next I continued with the configuration of the desktop computer (running debain etch 4.0 stable):
on the desktop: ping 192.168.1.101 -> ok, ping 192.168.1.201 -> not working zaurus: ping 192.168.1.201 -> ok, ping 192.168.1.101 -> not working Hm, obviously there is something wrong with my configuration I m somewhat stuck, any help would be greatly appreciated Thanks in advance olaf |
| Forum: Angstrom & OpenZaurus · Post Preview: #180285 · Replies: 6 · Views: 8,088 |
| Posted on: Sep 24 2007, 06:34 AM | |
|
Group: Members Posts: 4 Joined: 16-September 07 Member No.: 20,407
|
Hi all, recently my dad purchased a Zaurus sl-c1000 and told me to install something more useful on it  This is what i wanted to get working on the Zaurus: -simple windowmanager (fluxbox, blackbox,fvwm) -multiuser setup -native development (fortran, c++) -programs like xpdf, gnumeric -properly suspend Until now I ve tried out the last version of OZ with gpe, pdaXrom and pdaXiirom On both, pdaXrom and pdaXiirom, suspend has been a problem. Not sure why, Is that a common problem with those Roms? The last Rom i installed, has been OZ. Suspending and multiuser setup works very well. I even managed to get gcc working. Next I installed blackbox because i wanted something more useful than gpe  but it wasnt working because of the disabled colormanagement in X11. (i tried to recompile x11 with colormanagement enabled, but no success) Which Rom would you suggest me to use? Is angstrom a try worth? Thanks in advance olaf |
| Forum: Software · Post Preview: #167871 · Replies: 5 · Views: 3,453 |
 New Replies No New Replies Hot Topic (New) Hot Topic (No New) |
 Poll (New) Poll (No New) Locked Topic Moved Topic |
|
Lo-Fi Version | Time is now: 20th February 2019 - 04:36 AM |