Bluetooth Dial-up With A Sprint Treo 650

[ccrandal69]

I was able to get an internet connection from my Sprint Treo 650 to my old Clie UX-50, but I cannot do the same with the Zaurus.  I'm hoping someone here can help.

I am using a Zaurus SL C-760 with Socket Bluetooth Rev F card and running Cacko 1.23.  Initially, I had my Treo set so that DUN was turned off.  That's the only way I could get the Zaurus to recognize the Treo.  In the Network Applet, I successfully located the Treo, set up the user/pass as qnc/qnc, and set it to dial #777.  On the Treo I turned DUN on, but nothing happens when I try to initiate a dialup connection.  With the DUN turned off on the Treo, the bluetooth symbol on the Treo lights up, but still nothing.

I'm not sure what else to try.  Any ideas?

Thanks
Curt

[metal9966]

I was able to get an internet connection from my Sprint Treo 650 to my old Clie UX-50, but I cannot do the same with the Zaurus.  I'm hoping someone here can help.

I am using a Zaurus SL C-760 with Socket Bluetooth Rev F card and running Cacko 1.23.  Initially, I had my Treo set so that DUN was turned off.  That's the only way I could get the Zaurus to recognize the Treo.  In the Network Applet, I successfully located the Treo, set up the user/pass as qnc/qnc, and set it to dial #777.  On the Treo I turned DUN on, but nothing happens when I try to initiate a dialup connection.  With the DUN turned off on the Treo, the bluetooth symbol on the Treo lights up, but still nothing.

I'm not sure what else to try.  Any ideas?

Thanks
Curt
[div align=\"right\"][a href=\"index.php?act=findpost&pid=137107\"][{POST_SNAPBACK}][/a][/div]

I do bluetooth dialup with my Palm T5 and my laptop to my Treo 650 with Sprint. And it works great, Note that the treo 650 does NOTHING with the laptop or T5 connect, as the treo is still usable as a PDA during the connection, (only phone and The Treos access to data are blocked at this time)

Also It took alot of trial and error even before I got my Palm T5 to connect to the Treo 650 for dial-up. I do remember that i had to download a updated profile for the T5 to connect to the Treo 650 as well.

Good luck getting it to work as Blue-tooth is a major pain.

-Daniel

[ccrandal69]

I do bluetooth dialup with my Palm T5 and my laptop to my Treo 650 with Sprint. And it works great, Note that the treo 650 does NOTHING with the laptop or T5 connect, as the treo is still usable as a PDA during the connection, (only phone and The Treos access to data are blocked at this time)

Also It took alot of trial and error even before I got my Palm T5 to connect to the Treo 650 for dial-up. I do remember that i had to download a updated profile for the T5 to connect to the Treo 650 as well.

Good luck getting it to work as Blue-tooth is a major pain.

-Daniel
[div align=\"right\"][a href=\"index.php?act=findpost&pid=137204\"][{POST_SNAPBACK}][/a][/div]

Thanks for the encouragement.

Still no luck getting this to work.  I had no problems on the UX-50, so I was certain it'd work on the Zaurus... my old GSM phones connected easily.

I did try to redo everything and I made a little tweak this time:

1.) Turned on DUN on the Treo
2.) Went to the Network Applet on the Zaurus, in the Bluetooth tab I searched for the Treo
3.) When the Treo was found, the Treo displayed the dialog box for me to enter the pin for the Zaurus in... I entered 1234 and then the Zaurus showed up in my Trusted Devices list.
4.) Set up parameters in the Network tab:
Username: qnc
Password: qnc
Phone: #777
Dial Using: Tone
These parameters work fine on the UX-50
5.) Set up the modem parameters:
BT device: /dev/rfcomm0
Init String: ATZ (also tried a blank string)
Speed: 115200 (tried lower values too)
Time out: 5 and 15
6.) Left all other parameters alone.

When trying to connect, nothing happens.