Author Topic: F8t020 Bluetooth  (Read 2454 times)

Capn_Fish

  • Hero Member
  • *****
  • Posts: 2342
    • View Profile
    • http://
F8t020 Bluetooth
« on: August 31, 2006, 10:43:45 am »
I have a belkin F8T020 Bluetooth card that worked fine under Cacko, but is recognized as a Compaq Ipaq Bluetooth Sleeve when I insert it after installing the bluez stuff on pdaXrom. I saw an older thread about it, but the files mentioned weren't on my zaurus. Is there an order I'm supposed to install the packages in? I would also like some instructions on how to get this card to work, or some stuff to try.

Thanks in advance!
SL-C750- pdaXrom beta 1 (mostly unused)
Current distro: Gentoo

wowo123

  • Jr. Member
  • **
  • Posts: 81
    • View Profile
    • http://
F8t020 Bluetooth
« Reply #1 on: September 01, 2006, 07:44:23 am »
I use this card on a C3200 with beta3, but it also worked fine on a C860.
Enclosed you will find two conf-files. You have to put  bt-uart.conf in /etc/bluetooth and  bluetooth.conf in /etc/pcmcia. After resetting bluez the card should be recognized and function properly although cardctl ident may still call it  "generic". Good luck!

Capn_Fish

  • Hero Member
  • *****
  • Posts: 2342
    • View Profile
    • http://
F8t020 Bluetooth
« Reply #2 on: September 01, 2006, 09:36:12 am »
Thanks a lot! I'm currently reflashing my Zaurus to get rid of any changes I may have made to the Bluez files. I would like to know how to reset bluez. Thanks again!
SL-C750- pdaXrom beta 1 (mostly unused)
Current distro: Gentoo

Capn_Fish

  • Hero Member
  • *****
  • Posts: 2342
    • View Profile
    • http://
F8t020 Bluetooth
« Reply #3 on: September 01, 2006, 10:18:40 am »
How can I tell if bluetooth is working, and what command would I use to connect to my bluetooth mouse? The card applet still shows it as the ipaq bluetooth sleeve. Is this the way it is on yours?

Thanks for your help!
« Last Edit: September 01, 2006, 10:32:54 am by Capn_Fish »
SL-C750- pdaXrom beta 1 (mostly unused)
Current distro: Gentoo

wowo123

  • Jr. Member
  • **
  • Posts: 81
    • View Profile
    • http://
F8t020 Bluetooth
« Reply #4 on: September 02, 2006, 12:44:10 pm »
After changing the files (and deleting the old ones!) you should restart bluez: => /etc/rc.d/init.d/bluetooth restart. You can reboot as well. After your system came up, you put the card into the slot and there must be a short flash on the green card LED. When the LED stays dark or green something went wrong and you have to control the files again. When you activate the panel applet for the cf slot, your card should be properly recognized as BELKIN...When you reach this point, your bluez should run. With => sdptool browse   you should get a list of active BT-peers with MAC-address and all services and channels you can use. I think for your BT-mouse you should use the serial port but I don't know for I don't use anything like that.
Good luck!

Capn_Fish

  • Hero Member
  • *****
  • Posts: 2342
    • View Profile
    • http://
F8t020 Bluetooth
« Reply #5 on: September 02, 2006, 02:05:25 pm »
IT WORKS!!! THANK YOU THANK YOU!!!  Now all I have to do is figure out how to connect to my mouse.
SL-C750- pdaXrom beta 1 (mostly unused)
Current distro: Gentoo