Author Topic: How To Compile Modules? (Read 21895 times)

climber · « **Reply #45 on:** February 14, 2008, 08:37:57 am »

What do you mean that I can flash the kernel form the nomal OS? The command nandlogical isn't available there or if you mean something different then please write some detailed instructions (please).

Which modules do you mean to untar to /

Thanks
climber

Capn_Fish · « **Reply #46 on:** February 14, 2008, 12:13:59 pm »

In post 36 of this thread, there are 4 attachments:

-HostAP utils (not necessary unless you want to flash firmware)
-macchanger (was the only way to make my card inject for some reason, works fine without it now, not necessary)
-uimage (not a text file, it's the kernel, necessary)
-lib.tar.gz (the modules, necessary)

Then flash the kernel (however you can) and untar the lib.tar.gz package to / (remove the old /lib/modules/2.6.16 directory first).

Or just get the junk.tar.gz file from post #40 and:

-untar to some location
-flash the kernel (however you can)
-rm -r /lib/modules/2.6.16
-cd /
-tar -xf /path/to/modules.tar.gz

Hope that's enough information.
H

Capn_Fish · « **Reply #47 on:** February 15, 2008, 07:48:29 am »

No idea. I would guess so, but what's wrong with r198? It basically is r121, except with fixes.

climber · « **Reply #48 on:** February 15, 2008, 08:15:28 am »

One last questions before I start.

I never had installed r198 before so I read some entries in this forum. What I read look like that I first have to install U-boot
following these two links: Link1 Link2

Inside this link Link3 they talke about " .....NOTE: first release of emergency system for C1000/3x00 can't updating by this way...".
I have a SL-C3100 so which one of the 3 mentioned U-boot installation/upgrade versions should I take?

Thanks
climber

Capn_Fish · « **Reply #49 on:** February 15, 2008, 01:34:12 pm »

Put the files on a FAT-16 SD or CF (remove other card), remove all power from Z, hold C+D, insert AC. LEDs should come on for a bit, then go off. When they do, remove the power and flash r198*.

*Put the files on SD/CF, insert battery/power while holding OK, wait for it to boot and say "pdaX emergency system", answer 'y' to the question.

climber · « **Reply #50 on:** February 20, 2008, 05:56:43 am »

You told before that I can flash the kernel from the normal OS. Is it the
"nandlogical /dev/mtd1 WRITE 0x5a0000 0x160000 uImage" command. I only ask because this command isn't available
on pdaXii13v2.

Thanks
climber

Capn_Fish · « **Reply #51 on:** February 20, 2008, 07:38:53 am »

It's available on r198, that's about all I know. I have never used pdaXii13, so I'm afraid I cannot be much help, or even come close to guaranteeing that this kernel will work.

What exactly are you trying to do here (eg, what setup)? I've been kind of getting mixed impressions.

Capn_Fish · « **Reply #52 on:** February 22, 2008, 08:26:16 pm »

I just realized I uploaded the kernel, instructions, and a flashing script to

http://www.techassassins.com/Zaurus/junk/aircrack/

climber · « **Reply #53 on:** February 26, 2008, 03:40:29 am »

Is it possible to get the packet injection working for pdaXii13v2 with 2.4.20 kernel?

Thanks
climber

Capn_Fish · « **Reply #54 on:** February 27, 2008, 06:12:48 pm »

Yes it is possible, maybe with the modules posted on some website (I believe there was a link in your other thread).

If it needs the drivers recompiled, I can't help you. I've tried twice in the past with no luck, and have no intention of trying again in the near future. Sorry.

News:

Author Topic: How To Compile Modules? (Read 21895 times)