Canon K30225 Cf Wifi

[gojira]

There are some cheap Canon K30225 CF wifi cards on ebay at the moment.  Anyone using one with debian?  Thanks.

[axeTail]

There are some cheap Canon K30225 CF wifi cards on ebay at the moment.  Anyone using one with debian?  Thanks.

I'm currently based in South Africa and cf WIFI cards are impossible to find

[axeTail]

There are some cheap Canon K30225 CF wifi cards on ebay at the moment.  Anyone using one with debian?  Thanks.

Has anyone tried the SparkLAN WL-672 Wireless Compact Flash? Does it work?

[skywarrior1]

Bought one last month for a 2200 series Ipaq.  Came with no driver which auction said included. note that their auctions now say does NOT include CD.They did not respond to requests for drivers instead sent me to a site that had drivers for downloading which could not be uploaded into XP or Vista.
Nice card though. My 5 year old loves it for her dollhouse.  Get an SDIO and pay.

[kkazakov13]

I'm using exactly the same Canon on pdaXrom beta 3 without any problem. Worked out of the box, so I doubt you will have any problem with debian.

[AltairTK]

I'm using exactly the same Canon on pdaXrom beta 3 without any problem. Worked out of the box, so I doubt you will have any problem with debian.

I'm using exactly the same Canon too, on Sharp Zaurus C1000 with "Andromeda" filesystem and kernel 2.6.24-4yonggun. Work perfectly and when connect it to my Z. it's autoconfigure as eth1 interface.

[same]

I'm using exactly the same Canon on pdaXrom beta 3 without any problem. Worked out of the box, so I doubt you will have any problem with debian.

I'm using exactly the same Canon too, on Sharp Zaurus C1000 with "Andromeda" filesystem and kernel 2.6.24-4yonggun. Work perfectly and when connect it to my Z. it's autoconfigure as eth1 interface.

I also installed debian-andromeda, but the canon k30225 can't be detected. I see there's no hostap_cs.conf file in /etc/pcmcia (planex gw-cf11h working with andromeda and hostap)
It's being detected and working under pdaxrom

Any ideas? thanks

[speculatrix]

I also installed debian-andromeda, but the canon k30225 can't be detected. I see there's no hostap_cs.conf file in /etc/pcmcia (planex gw-cf11h working with andromeda

do the usual thing... "pccardctl ident" and status and inquiry etc etc, and let us know what you see. might need to do pccardctl resume before hand. (cardctl and pccardctl are equivalent commands depending on age of distro)

[same]

hello,

Code: [Select]

yonggun:~# pccardctl info 1
PRODID_1="Canon"
PRODID_2="Wireless LAN CF Card K30225"
PRODID_3="Version 01.00"
PRODID_4=""
MANFID=0004,2003
FUNCID=6

yonggun:~# pccardctl status 1
  3.3V 16-bit PC Card
  Subdevice 0 (function 0) [unbound]

yonggun:~# pccardctl ident 1
  product info: "Canon", "Wireless LAN CF Card K30225", "Version 01.00", ""
  manfid: 0x0004, 0x2003
  function: 6 (network)

yonggun:~# dmesg | tail -n 2
pccard: PCMCIA card inserted into slot 1
pcmcia: registering new device pcmcia1.0
tried loads of things for days with no success, maybe I googled with wrong keywords for this issue, but no doc related or working for me. planex card is failing and need to replace it

thanks for your attention

[speculatrix]

it looks like this is a prism2 card with alternative ident... you should be able to modify your /etc/pcmcia/wlan-ng.conf (or equivalent file) to add lines like this:

card "Canon Wireless LAN CF Card K30225"
manfid 0x0004,0x2003
bind "prism2_cs"

[same]

added

Code: [Select]

card "Canon Wireless LAN CF Card K30225"
manfid 0x0004,0x2003
bind "prism2_cs"but main problem is that cant build prims2_cs with module-assistant as there's no linux headers

added

Code: [Select]

card "Canon Wireless LAN CF Card K30225"
manfid 0x0004,0x2003
bind "hostap_cs"to /etc/pcmcia/config

added SYSFS{manf_id} and SYSFS{card_id} in /etc/udev/rules.../70-persistent-net.rules with mac and all

tried also creating a rules file in same folder with

Code: [Select]

ACTION=="add", SYSFS{manf_id}=="0x0004", SYSFS{card_id}=="0x2003", SYSFS{func_id}=="0x06", \
         RUN+="/sbin/modprobe hostap_cs ignore_cis_vcc=1"

ACTION=="add", SYSFS{manf_id}=="0x0004", SYSFS{card_id}=="0x2003", SYSFS{func_id}=="0x04", \
         OPTIONS="last_rule"
edited the udev rules generation for net disabling all ignore conditions.

added options hostap_cs ignore_cis_vcc=1 to /etc/modules and modules.conf

nothing has any minimal effect, always get the:

Code: [Select]

pccard: PCMCIA card inserted into slot 1
pcmcia: registering new device pcmcia1.0
i can't even get a debug message that shows me the next step, always the same reply no matter what i do  

[same]

http://lists.infradead.org/pipermail/linux...ary/005305.html
after reading this i don't know if it's possible to bring that card up using the custom yonggun kernel
[size=]
but seing the previous post from AltairTK

I'm using exactly the same Canon too, on Sharp Zaurus C1000 with "Andromeda" filesystem and kernel 2.6.24-4yonggun. Work perfectly and when connect it to my Z. it's autoconfigure as eth1 interface.

it's confusing, did a fresh andromeda install and nothing configured as eth1, as expected
i would like to see a lspcmcia -vvv of AltairTK's card just to check that it's not a different card[/size]

edit: i see in /hostap-driver-0.4.9/driver/modules/hostap_cs.c L:935

Code: [Select]

#if (LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,13))
static struct pcmcia_device_id hostap_cs_ids[] = {
    PCMCIA_DEVICE_MANF_CARD(0x000b, 0x7100),
    PCMCIA_DEVICE_MANF_CARD(0x000b, 0x7300),
...seems manfids are hardcoded in hostap driver?! 2or0 please  
thanks

[same]

SOLVED, hexedited hostap_cs.ko, always backup the original file first!

finally, after some time forgeting it as planex card was (half)working it forced me to start checking this ebay-Canon card again.

1) i found that the same Canon K30225 might have two different manfid:

I guess AltairTK K30225 card is

Identification: manf_id: 0x0156 card_id: 0x0002
   function: 6 (network)
   prod_id(1): "Wireless LAN" (0x4b8870ff)
   prod_id(2): "11Mbps PC Card" (0x70e946d1)
   prod_id(3): "Version 01.02" (0x4b74baa0)
   prod_id(4): --- (---)

as seing in http://article.gmane.org/gmane.linux.distr...93/match=k30225

while my K30225 card is

product info: "Canon", "Wireless LAN CF Card K30225", "Version 01.00", ""
  manfid: 0x0004, 0x2003
  function: 6 (network)

hostap_cs.ko (.c with source) has

Code: [Select]

    PCMCIA_DEVICE_MANF_CARD_PROD_ID1(0x0156, 0x0002, "INTERSIL",
                     0x74c5e40d),
    PCMCIA_DEVICE_MANF_CARD_PROD_ID1(0x0156, 0x0002, "Intersil",
                     0x4b801a17),and might detect AltairTK's card, but hasn't 0x0004, 0x2003 (my K30225) anywhere in source file
2) forcing the detection of my card hexediting /lib/modules/(...)/wireles/hostap/hostap_cs.ko
[blockquote]* i first searched for the (text) string "m000Bc7100" and changed it to "m0004c2003"
* then searched for the hex string "0B 00 00 71" and changed it to "04 00 03 20".[/blockquote]
got the idea from here: http://sin613.blogspot.com/2007/02/i-win.html

modified hostap_cs.ko attached: dload and untar it in the /lib/modules/(...)/net/wireles/hostap/ folder

[speculatrix]

well done, your persistence has paid off

I am reminded of how people discovered that the original (cheaper) Orinoco silver cards (40 bit wep) were identical to the more expensive Orinoco gold cards (full 128 bit wep), with only a different ident, so that the driver refused to use a larger key. People were able to hack the windows driver, and then someone hacked the firmware updater which allowed you to turn a silver into a gold!

[AltairTK]

Hi,
my wireless-cfcard work perfectly if i used a no-protected wifi connection (i have not tested with WEP encryption) because when i plugged in automatically load the orinoco driver.
If i insert Orinoco in blacklist and manually modprobe hostap my card is recognised as pcmcia but no network adapter is added (eth1, wlan0 ecc...)

-- For Same --
this is my output of dmesg when i plugged the card:

pccard: PCMCIA card inserted into slot 0
pcmcia: registering new device pcmcia0.0
pcmcia: request for exclusive IRQ could not be fulfilled.
pcmcia: the driver needs updating to supported shared IRQ lines.
eth0: Hardware identity 801b:0000:0001:0000
eth0: Station identity  001f:0004:0001:0008
eth0: Firmware determined as Intersil 1.8.4
eth0: Ad-hoc demo mode supported
eth0: IEEE standard IBSS ad-hoc mode supported
eth0: WEP supported, 104-bit key
eth0: MAC address 00:00:85:31:e2:33
eth0: Station name "Prism  I"
eth0: ready
eth0: orinoco_cs at 0.0, irq 169, io 0xc4820000-0xc482003f
udev: renamed network interface eth0 to eth1


and the output of lspcmcia & pccardctl:


yonggun:/sbin# pccardctl ls
Socket 0 Bridge:      [pxa2xx-pcmcia]    (bus ID: pxa2xx-pcmcia)
Socket 0 Device 0:   [orinoco_cs]      (bus ID: 0.0)

yonggun:/sbin# pccardctl info
PRODID_1="Wireless LAN"
PRODID_2="11Mbps PC Card"
PRODID_3="Version 01.02"
PRODID_4=""
MANFID=0156,0002
FUNCID=6

yonggun:/sbin# pccardctl ident
Socket 0:
  product info: "Wireless LAN", "11Mbps PC Card", "Version 01.02", ""
  manfid: 0x0156, 0x0002
  function: 6 (network)


-------

With orinoco drivers i have some problems with my Router and wpa encryption. I think it's not supported ( eth0: WEP supported, 104-bit key );
when i launch wpa_supplicant, iwlist, wpa_gui and wifi-radar detect my network but the led of connection is not fixed and wpa_supplicant enter in a continuous scan loop (i try wext and wired drivers).
Now I try to make the change, suggested by Same, in the configuration file of pcmcia card and to udev for (i hope) use HostAP instead of Orinoco.