Messages

1

Security and Networking / Can't Pair New Bluetooth Device?

« on: December 09, 2005, 11:34:13 pm »

I've been using bluetooth to connect to my PC and mobile phone for a long time in cacko 1.22a.  Recently, I've changed my mobile to 3G (Nokia N70), my Zaurus couldn't pair to the new phone.  In the syslog, it showed "PIN helper exited abnormally with code 32265".

Afterwards, I couldn't pair to any new device??

Any advice of the code 32265??  It seems it is the password issue but my /etc/bluetooth/givepin and /etc/bluetooth/pin have not been changed.

2

General Discussion / stalled file uploads

« on: November 11, 2005, 05:12:29 am »

i have exactly the same problem w/ bluetooth connection.  i don't know the complete solution at the moment but i found that underclocking made the connection more stable.

3

Security and Networking / Help! Wlan Not Working

« on: November 05, 2005, 09:46:56 am »

bingo! i finally get my z connecting to my home wifi!

a silly mistake: I've a space in my ESSID....

4

Security and Networking / Help! Wlan Not Working

« on: November 04, 2005, 10:50:34 pm »

by luck, the network connection icon and connect button works again!    

next, i need to connect the z to my wifi.....

5

Security and Networking / Help! Wlan Not Working

« on: November 03, 2005, 10:19:06 pm »

I've played around cardctl w/ my cf bt card and found that the network connection icon should appear when I used cardctl insert.  I'm now narrowing down my investigation to "what are the steps for cardctl insert"?

6

Security and Networking / Help! Wlan Not Working

« on: November 03, 2005, 08:57:01 pm »

The ESSID to "any" does not works.

Write the correct ESSID and try to connect.

And the same thing happens on mi c700 after a reboot with the wifi inside. just remove and reinsert (with the remove icon), and the connection icon will appear.
[div align=\"right\"][a href=\"index.php?act=findpost&pid=102164\"][{POST_SNAPBACK}][/a][/div]

Thanks seinfield.

I've tried a correct ESSID but it did not work.  Don't know whether this is a compatibility issue between my Pretec wifi and Planex wireless router.

BTW, I still cannot make the connection icon appear.  Though I managed to kick the card in by using cardctl scheme CardResume, the connection icon still disappeared.  cardctl ident showed correct info.  Here are what I've tried:

- reboot
- card reject and reinsert by using the remove icon and cardctl
- delete all other entries of hostap_cs.conf except my pretec card
- using cardctl scheme qpewlan0 to start the network connection

I suspect there is somewhere in the network connection program that has remembered incorrect card status.

 

7

Security and Networking / Help! Wlan Not Working

« on: November 02, 2005, 10:59:14 am »

some more info: when I do cardctl status, the card status is suspended.  I've tried reset the card but status unchange.

i don't believe I've damaged my card just by simple reboot!     any thing i can try?

8

Security and Networking / Help! Wlan Not Working

« on: November 02, 2005, 10:13:49 am »

I've just got a Pretec wlan card and plugged into my C760 w/ cacko rom 1.22a.

At first, I've got the card recognized and created a network connection "any".

But it just can't connect and after a while just dropped out.

Then I tried to reboot but after reboot, the network connection icon at the taskbar disappeared!  When I kicked in the network connection, it just has the "connect" button dim.

 

anyone can help?  

9

Sharp ROMs / Slow Performance With C760 And Cacko 1.22

« on: January 30, 2005, 09:22:33 pm »

you may activate too many fastload.  try to:
- tap on the icon, say datebook
- hold for a few sec
- uncheck "Fast Load"

hope this help.

10

Software / Gmail Pop Access?

« on: December 10, 2004, 01:44:14 am »

i'm using om/pi to access gmail.  btw, i can successfully connect to gmail smtp for sending email.  for pop3, i can connect and download email, but i'm still figuring out the rule of downloading.  it seems to me that it is not downloading email in inbox.

11

Software / KDE-Pim/Pi 1.9.7 Release

« on: October 18, 2004, 11:47:18 pm »

Hi,

For my problem of event/To-do not erasable, the solution was :
1) Remove file mycalendar.ics
2) Sync with Sharp DTM

And all became as it was before  

Thanks for this great software suite.
It helps me daily for my job.

plcg

plcg, thanks a lot.  that solves a lot of my troubles.

12

Software / KDE-Pim/Pi 1.9.7 Release

« on: October 18, 2004, 11:22:22 pm »

anyone using 1.9.7 has dtm syncing problem w/ outlook?  when using previous version, it works perfectly.  however, in 1.9.7, i can only sync with outlook after i quit kopi and fastload disabled.  if not, i'll get an API error in my pc.

i'll log the problem in sourceforge as well.

13

Software / KDE-Pim/Pi 1.9.6 Release

« on: October 10, 2004, 11:00:52 pm »

$ cd kdepim/apps/kabc
$ mv std.vcf std.vcf.old
$ tr -d '\r' < std.vcf.old > std.vcf

that works for me as well.

14

Software / KDE-Pim/Pi 1.9.6 Release

« on: September 28, 2004, 12:15:44 am »

It's me again with another (real) problem. I imported all my data from DTM to KA/PI, did some edits and exited. KA/PI. I then tried starting KA/PI again and it didn't start. Starting from the command line gives:
This happens immediately, I get no KA/PI screen. I would think it might be a problem with the .vcf file (I have almost 500 contacts in it). So, is there a way of finding out exactly which entry it's crashing at? Perhaps a command-line switch or an environment variable that would list every entry it reads so it's possible to debug.

Thank you for testing the KDEPim suite.

There is probably something wrong with one of the contacts in your file.
Please close Ka/Pi, then take your addressbookfile (/home/zaurus/kdepim/apps/kabc/std.vcf) and try to find out which entry (contact) causes the crash. You can do that with a try and error approach and split the file always halfways.

I will think about a debug option while loading contacts. But this option will be first available in one of the next versions.

Ah, and guys, if you have enhancement requests or real bugs like this one, please post them also at sourceforge. That helps us to keep track on things.

thanks,
Ulf

no no, i have similar problem but different error msg.  see here.

btw, i've inputted an entry in sourceforge.

15

Software / KDE-Pim/Pi 1.9.6 Release

« on: September 24, 2004, 06:45:22 am »

- can't open ompi in gui.  i've got an error msg of missing libssl.so.0.9.7 but i can't find in ZSI.

anyway, zautrix, this is the most useful app for me (except ompi which i still can't open it) in z.  thx.

finally, i got the libssl.  however, the email downloading is very slow, much slower than using qtmail.  in addition, i always get error message "error 5 initializing folder" when i click "inbox".