Messages

1

6000 - Tosa / Unable To Connect To Linksys Ap, Adhoc Works Fine

« on: February 19, 2005, 10:05:06 pm »

Yes, i have tryed specifiying the SSID and with out.

I'm quite certain this is a software issue with the Zaurus, since it worked with Open Zaurus.

I am running a SL-6000 (standard sharp rom 1.1.2) and a Linksys WRT54G, with WEP, and it works fine.

Have the MAC address remain all zeros sounds like it isn't associating with the AP correctly. Have you typed in the SSID of the AP, or is it set to Any?

Craig...
[div align=\"right\"][a href=\"index.php?act=findpost&pid=67807\"][{POST_SNAPBACK}][/a][/div]

2

6000 - Tosa / Unable To Connect To Linksys Ap, Adhoc Works Fine

« on: February 18, 2005, 09:19:20 am »

My neighbor, 2 houses over does have a netgear, with wep enablied. He runs on channel 11. I run on 6. I have tried 1 as well. Same problem. I have tried this being right next to my AP and about as fasr away as 50 feet. I do geive it the SSID and i have tried it without and get a similar results. I seem to do better when i specifiy the settings.  My AP is set to 192.168.254.1. I did a full reset on it so that it was back at 192.168.1.1 and experienced the same issue.

Could a nearby neighbor's router be interfering? Try walking closer to your own router to see if it makes a difference. Also, you did not mention whether you entered your essid & gateway (probably 192.168.1.1). Also check for unnecessary proxy entries.
[div align=\"right\"][a href=\"index.php?act=findpost&pid=67624\"][{POST_SNAPBACK}][/a][/div]

3

6000 - Tosa / Unable To Connect To Linksys Ap, Adhoc Works Fine

« on: February 17, 2005, 10:03:06 pm »

No matter what my setting are (static/dhcp) i cannot connect to my AP (Linksys WRT54G with stock 2.2db and replacement 5.5db antennas) at home. If I go to Settings/Network/ and select the Current tab The status  and watch the connection process I see the MAC convert from all 0's to the actual MAC. The AP address always remains all 0's. I get a 51-80% signal, but the quality remains 0%.  It will try and connect and then state in a pop up titled "Connection Setup Error" The error is "No Connection detected. Check your TCP/IP settings." The only option is to click on OK.

I shipped the unit into Sharp thinging something was wrong, they sent it back stating that everythign was fine.

So i installed OpenZaurus 3.5.2 w/Opie. The wireless worked fine at home. So this confirms to me that it has something to do with the Sharp ROM.  I reinstalled the Sharp ROM and the problem returned.

Any Ideas?

Yes i have tried changing the channel. 1, 6, and 11.
also tried with and without WEP and with and without MAC filtering

4

6000 - Tosa / Unable To Connect To Linksys Ap, Adhoc Works Fine

« on: February 17, 2005, 10:02:06 pm »

No matter what my setting are (static/dhcp) i cannot connect to my AP (Linksys WRT54G with stock 2.2db and replacement 5.5db antennas) at home. If I go to Settings/Network/ and select the Current tab The status  and watch the connection process I see the MAC convert from all 0's to the actual MAC. The AP address always remains all 0's. I get a 51-80% signal, but the quality remains 0%.  It will try and connect and then state in a pop up titled "Connection Setup Error" The error is "No Connection detected. Check your TCP/IP settings." The only option is to click on OK.

I shipped the unit into Sharp thinging something was wrong, they sent it back stating that everythign was fine.

So i installed OpenZaurus 3.5.2 w/Opie. The wireless worked fine at home. So this confirms to me that it has something to do with the Sharp ROM.  I reinstalled the Sharp ROM and the problem returned.

Any Ideas?

Yes i have tried changing the channel. 1, 6, and 11.
also tried with and without WEP and with and without MAC filtering

5

6000 - Tosa / WiFi bug

« on: February 17, 2005, 09:59:03 pm »

No matter what my setting are (static/dhcp) i cannot connect to my AP (Linksys WRT54G with stock 2.2db and replacement 5.5db antennas) at home. If I go to Settings/Network/ and select the Current tab The status  and watch the connection process I see the MAC convert from all 0's to the actual MAC. The AP address always remains all 0's. I get a 51-80% signal, but the quality remains 0%.  It will try and connect and then state in a pop up titled "Connection Setup Error" The error is "No Connection detected. Check your TCP/IP settings." The only option is to click on OK.

I shipped the unit into Sharp thinging something was wrong, they sent it back stating that everythign was fine.

So i installed OpenZaurus 3.5.2 w/Opie. The wireless worked fine at home. So this confirms to me that it has something to do with the Sharp ROM.  I reinstalled the Sharp ROM and the problem returned.

Any Ideas?

Yes i have tried changing the channel. 1, 6, and 11.
also tried with and without WEP and with and without MAC filtering

6

Las Vegas / HEllo?

« on: March 27, 2004, 11:40:15 am »

C\'mon.. anyone here in vegas?

The Las Vegas Linux User Group www.lvlug.org has a few member interested in starting a Linux PDA SIG. Zaurus and iPaq as i understand it.