Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - whykickamoocow

Pages: [1] 2
1
Ubuntu / Apt-get In Zubuntu
« on: May 13, 2009, 08:24:18 pm »
I would just like to thank everbody on here who has help me out with this, at last i got it connected with wep, to all those who are like me a complete newbie, please just follow this post to get connected to your router. At times you will feel like banging your head but if you follow this post then all the hard must be done for you, im not sure on a cpl of thingsi have done to make this work, i need to read up about it,but at the end of the day it worked. thanks again.

Regards whykick

2
Ubuntu / Apt-get In Zubuntu
« on: May 13, 2009, 08:54:14 am »
I also get this message when i try this

[div class=\'codetop\']CODE[/div][div class=\'codemain\' style=\'height:200px;white-space:pre;overflow:auto\']root@Zubuntu:~# iwconfig wlan0 essid sukmebeautifull mode managed
root@Zubuntu:~# ifup wlan0
There is already a pid file /var/run/dhclient.wlan0.pid with pid 0
Internet Systems Consortium DHCP Client V3.0.6
Copyright 2004-2007 Internet Systems Consortium.
All rights reserved.
For info, please visit http://www.isc.org/sw/dhcp/

wifi0: unknown hardware address type 801
Can't create addrlist socket
Failed to bring up wlan0.
root@Zubuntu:~# ifup wlan0
There is already a pid file /var/run/dhclient.wlan0.pid with pid 0
Internet Systems Consortium DHCP Client V3.0.6
Copyright 2004-2007 Internet Systems Consortium.
All rights reserved.
For info, please visit http://www.isc.org/sw/dhcp/

wifi0: unknown hardware address type 801
Can't create addrlist socket
Failed to bring up wlan0.
root@Zubuntu:~# [/div]



Regards whykick

3
Ubuntu / Apt-get In Zubuntu
« on: May 13, 2009, 08:08:12 am »
Yeah that seemed to have worked,when i do a lsmod i dont see the orinoco or the hermes anymore, when i do the ifconfig i get the wifi0 and the wlan0 and both seem to look ok. when i use wifi radar to connect to my router it connects but it cant find the ip addy,swo its sort of halfway there but i still cant connect to the internet.Anybody got any ideas?

Regards whykick

4
Ubuntu / Apt-get In Zubuntu
« on: May 08, 2009, 07:13:19 pm »
Thanks for the help guys but i think its a little ove rmy head now,im still pretty new to linux and i think i have a hell of a way b4 im up to your standrds. I did a lsmod and this is what it came up with, i realy dont know what im looking at.

[div class=\'codetop\']CODE[/div][div class=\'codemain\' style=\'height:200px;white-space:pre;overflow:auto\']root@Zubuntu:~# lsmod
Module                  Size  Used by
arc4                    1696  2
ecb                     2720  2
crypto_blkcipher       16388  1 ecb
cryptomgr               2752  0
crypto_algapi          14464  4 arc4,ecb,crypto_blkcipher,cryptomgr
ieee80211_crypt_wep     3712  0
orinoco_cs             13860  0
orinoco                40916  1 orinoco_cs
hermes                  5824  2 orinoco_cs,orinoco
hostap_cs              54772  3
hostap                104900  1 hostap_cs
ieee80211_crypt         4928  2 ieee80211_crypt_wep,hostap
uinput                  7904  1
autofs4                21060  0
snd_soc_spitz           5612  0
snd_soc_pxa2xx_i2s      3384  1 snd_soc_spitz
snd_soc_wm8750         18512  2 snd_soc_spitz
snd_soc_pxa2xx          4352  1 snd_soc_spitz
snd_soc_core           26336  3 snd_soc_spitz,snd_soc_wm8750,snd_soc_pxa2xx
snd_pcm_oss            39488  0
snd_pcm                71301  3 snd_soc_pxa2xx,snd_soc_core,snd_pcm_oss
snd_page_alloc          6216  1 snd_pcm
snd_mixer_oss          14752  1 snd_pcm_oss
snd_seq_midi            6240  0
snd_rawmidi            20672  1 snd_seq_midi
snd_seq_midi_event      6496  1 snd_seq_midi
snd_seq                52288  2 snd_seq_midi,snd_seq_midi_event
snd_timer              21124  2 snd_pcm,snd_seq
snd_seq_device          6796  3 snd_seq_midi,snd_rawmidi,snd_seq
snd                    46804  12 snd_soc_spitz,snd_soc_wm8750,snd_soc_core,snd_pcm_oss,snd_pcm,snd_mixer_oss,snd_
awmidi,snd_seq,snd_timer,snd_seq_device
soundcore               6564  1 snd
rfcomm                 36660  0
ircomm_tty             21256  0
ircomm                 11268  1 ircomm_tty
hidp                   14048  0
l2cap                  21092  4 rfcomm,hidp
bluetooth              54792  3 rfcomm,hidp,l2cap
usbhid                 19972  0
hid                    36676  2 hidp,usbhid
pxaficp_ir              9184  0
ohci_hcd               21288  0
pxa27x_udc             15620  0
irda                  107432  3 ircomm_tty,ircomm,pxaficp_ir
usbcore               127900  3 usbhid,ohci_hcd
mousedev               11652  1
root@Zubuntu:~#
[/div]


Regards whykick

5
Ubuntu / Apt-get In Zubuntu
« on: May 06, 2009, 05:53:40 pm »
Thats just how i had mine, then in a terminal i typed ifup wlan0 and it came up with this

[div class=\'codetop\']CODE[/div][div class=\'codemain\' style=\'height:200px;white-space:pre;overflow:auto\']root@Zubuntu:~# ifup wlan0
There is already a pid file /var/run/dhclient.wlan0.pid with pid 0
Internet Systems Consortium DHCP Client V3.0.6
Copyright 2004-2007 Internet Systems Consortium.
All rights reserved.
For info, please visit http://www.isc.org/sw/dhcp/

wifi0: unknown hardware address type 801
Can't create addrlist socket
Failed to bring up wlan0.
root@Zubuntu:~# [/div]

I also tried using wifi-radar but it was saying that it couldnt accuire the ip address, i feel i got a bit further and im sure i can fix the problem b4 the weeks out, but also need as much help as i can get. ive just had the same trouble with my jornada running jlime but thankfully i got that one sorted.

regards

6
Ubuntu / Apt-get In Zubuntu
« on: May 06, 2009, 12:43:34 pm »
How should my interface file look oliver when i add the auto wlan0, I just want to see the lay out of the file to make sure im doing it right.

Regards whykick

7
Ubuntu / Apt-get In Zubuntu
« on: May 04, 2009, 06:47:36 pm »
Hi
Ive tried all the things i have been shown on here and i am still having troubleconnecting to my router. Ive change my interface file to this

[div class=\'codetop\']CODE[/div][div class=\'codemain\' style=\'height:200px;white-space:pre;overflow:auto\']iface wlan0 inet dhcp
wireless_mode managed
wireless_essid sukmebeautifull
wireless_key xxxxxxxxx
wireless_channel 11[/div]

Which at first looked like this

[div class=\'codetop\']CODE[/div][div class=\'codemain\' style=\'height:200px;white-space:pre;overflow:auto\']# /etc/network/interfaces -- configuration file for ifup(8), ifdown(8)

# The loopback interface
auto wlan0
iface lo inet loopback

# Wireless interfaces
iface wlan0 inet dhcp
wireless_mode managed
wireless_essid sukmebeautifull
wireless_key xxxxxxxxxxxxxxxxxxxxxxxxxx
wireless_channel 11
iface atml0 inet dhcp

# Wired or wireless interfaces
iface wlan0 inet dhcp
iface wlan0 inet dhcp

# Ethernet/RNDIS gadget (g_ether)
# ... or on host side, usbnet and random hwaddr
iface usb0 inet static
address xxx.xxx.x.xx
netmask 255.255.255.0
network 192.168.0.0
gateway 192.168.1.253


# Zaurus 2.4 Lineo net_fd; obsolete
iface usbd0 inet static
address 92.16.215.3
netmask 255.255.255.0
network 192.168.0.0
gateway 192.168.1.253

# iPAQ 2.4 mach-sa1100/usb-eth
# (192.168.0.202 is the iPAQ's IP, 192.168.0.200 is the host's IP)
iface usbf inet static
address 92.16.215.3
netmask 255.255.255.0
network 192.168.0.0
gateway 192.168.1.253

# Bluetooth networking
iface bnep0 inet dhcp[/div]

This is what shows when i do ifconfig

[div class=\'codetop\']CODE[/div][div class=\'codemain\' style=\'height:200px;white-space:pre;overflow:auto\']root@Zubuntu:~# ifconfig          
lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0   TX bytes:0 (0.0 [/div]

And this is what shows when i do iwconfig

[div class=\'codetop\']CODE[/div][div class=\'codemain\' style=\'height:200px;white-space:pre;overflow:auto\']oot@Zubuntu:~# iwconfig
lo        no wireless extensions.

irda0     no wireless extensions.

wifi0     IEEE 802.11b  ESSID:" "  Nickname:""
          Mode:Managed  Access Point: Not-Associated   Bit Rate:2 Mb/s  
          Sensitivity=1/3  
          Retry short limit:8   RTS thr:off   Fragment thr:off
          Encryption key:off
          Power Management:off
         
wlan1     IEEE 802.11b  ESSID:" "  Nickname:""
          Mode:Managed  Access Point: Not-Associated   Bit Rate:2 Mb/s  
          Sensitivity=1/3  
          Retry short limit:8   RTS thr:off   Fragment thr:off
          Encryption key:off
          Power Management:off
          Link Quality=0/70  Signal level=-73 dBm  Noise level=-73 dBm
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0
[/div]

Can anybody tell me were i am going wrong.
many thanks

Regards whykick

8
Ubuntu / Apt-get In Zubuntu
« on: April 16, 2009, 01:35:12 pm »
Thanks for the replys, Im not that sure what the interface file is suppose to look like, my card comes up as wlan0 so i could do with all the help u can give me to get the right settings.

Regards whykick

9
Ubuntu / Apt-get In Zubuntu
« on: April 14, 2009, 03:09:32 pm »
im starting to bang my head against a wall,i must be missing somthing out here, i tried to ping in and also had ago at opening the firefox browser and it looks like i dont have a connection as i thought i did.  ive tried all ways to connect i.e with or without a wep key on and still comes up with nothing. ive installed wifi radar and for some reason it seems to it seems to connct to the wrong ip address, ive even checked my interface file and nothing is jumping out on me. Can somebody have a look at my interface setup and let me know were i am going wrong and what i need to do, also is it me or is everbody having trouble loading up firefox browser up as i was just wondering wether to plash out on a better sd card.



# /etc/network/interfaces -- configuration file for ifup(8), ifdown(8)
 
# The loopback interface
auto wlan0
iface lo inet loopback

# Wireless interfaces
iface wlan0 inet dhcp
wireless_mode managed
wireless_essid sukmebeautifull
wireless_key xxxxxxxxxxxxxxxxxxxxxxxxxx
wireless_channel 11
iface atml0 inet dhcp

# Wired or wireless interfaces
iface wlan0 inet dhcp
iface wlan0 inet dhcp

# Ethernet/RNDIS gadget (g_ether)
# ... or on host side, usbnet and random hwaddr
iface usb0 inet static
   address xxx.xxx.x.xx
   netmask 255.255.255.0
   network 192.168.0.0
   gateway 192.168.1.253


# Zaurus 2.4 Lineo net_fd; obsolete
iface usbd0 inet static
   address 92.16.215.3
   netmask 255.255.255.0
   network 192.168.0.0
   gateway 192.168.1.253

# iPAQ 2.4 mach-sa1100/usb-eth
# (192.168.0.202 is the iPAQ's IP, 192.168.0.200 is the host's IP)
iface usbf inet static
        address 92.16.215.3
        netmask 255.255.255.0
        network 192.168.0.0
        gateway 192.168.1.253

# Bluetooth networking
iface bnep0 inet dhcp


Regards Whykick

10
Ubuntu / Apt-get In Zubuntu
« on: April 13, 2009, 08:04:50 am »
Ive been trying to install aircrack onto my zaurus 3200 which has zubuntu running on it, When i try the command "apt-get install aircrack-ng" it come up with this message ever time,

root@Zubuntu:~# apt-get install aircrack-ng
Reading package lists... Done
Building dependency tree      
Reading state information... Done
The following NEW packages will be installed:
  aircrack-ng
0 upgraded, 1 newly installed, 0 to remove and 0 not upgraded.
Need to get 962kB of archives.
After this operation, 1716kB of additional disk space will be used.
Err http://repository.handhelds.org hasty/universe aircrack-ng 1:1.0~beta1-1
  Could not resolve 'repository.handhelds.org'
Failed to fetch http://repository.handhelds.org/hasty-armv...beta1-1_arm.deb  Could not resolve 'repository.handhelds.org'
E: Unable to fetch some archives, maybe run apt-get update or try with --fix-missing?
root@Zubuntu:~# aircrack-ng
bash: aircrack-ng: command not found
root@Zubuntu:~# airmon-ng
bash: airmon-ng: command not found
root@Zubuntu:~#


Ive tried all way to do this and had ago with other programs and it still comes up with the same. Whats the best way to install these programs in zubuntu or can sombody tell me were im going wrong.
One more thing, can sombody tell me how to check if i have a good internet connection with my zaurus.

Regards Whykick

11
Ubuntu / Zubuntu Wifi/internet
« on: March 30, 2009, 05:19:17 pm »
thanks for that chero, im using the trisoft one, When i type "ifup wlan0" this is the the error message that i am getting, "ignoring unknown interface wlan0=wlan0"

Any body got any ideas with this one,or is there an easy way to connect zubuntu to the internet?????

Regards

WHykick

12
Ubuntu / Zubuntu Wifi/internet
« on: March 26, 2009, 05:47:31 pm »
this is what comes up after i install the card and do a "dmesg".
The cards light flashing all the time and its WEP im tring to connect to with a encrytion key, so im not sure what im doing wrong, Is there a good program i can install on the zubuntu to get connected with or can i run a command through the shell to connect to my router.

hostap_cs: Registered netdevice wifi0
pcmcia: request for exclusive IRQ could not be fullfilled.
pcmcia: the driver needs updating to supported shared IRQ lines.
hostap_cs: index 0x01: , irq 169, io 0xc4840000-0xc484003f
prism2_hw_init: initialized in 210 ms
wifi0: NIC: id=0x800c v1.0.0
wifi0: PRI: id=0x15 v1.0.7
wifi0: STA: id=0x1f v1.3.5
wifi0: defaulting to bogus WDS frame as a workaround for firmware bug in Host AP mode WDS
wifi0: registered netdevice wlan0

Regards

whykick

13
Ubuntu / Zubuntu Wifi/internet
« on: March 25, 2009, 05:04:19 pm »
Can anybody tell me how they are connecting to the internet with zubuntu, Ive got the linksys wcf11 compact flash card but im having no luck at the moment. Any other ideas i would be interested in.

Regards

Whykick

14
Ubuntu / Zubuntu Help
« on: March 24, 2009, 06:03:08 pm »
thought i best post this just incase its some interest to some people, the problems i had in the previous post have all been sorted out. The problem was that i was downloading the files on a windows box and then extracting them on ubuntu, it just didnt like it. In the end i did everthing from the downloading to the extracting on the ubuntu os and now it works a treat. Would also like to thank everybody for there help with it.

Regards

Whykick

15
C1000/3x00 General discussions / Sl-c3100 Factory Reset Problems
« on: March 24, 2009, 05:50:47 pm »
Hi, i had the same message when i tried to do it with the figlabs cd and i thought the same that i had a duff, trisoft is a good one and ive also just got zubuntu working on mine.

Regards

Whykick

Pages: [1] 2