Messages

1

Security and Networking / Wpa-psk And 3.5.4

« on: April 14, 2006, 10:55:33 pm »

Update.

Hrw has uploaded a new wpa_supplicant (wpa-supplicant_0.4.8-r1_arm.ipk) to the upgrades feed that resolves Bug #819.

Note that with the Ambicom WL1100C you will need to use -Dwext instead of -Dhostap when starting wpa_supplicant.

Kudos to Hrw for the speedy resolution.

-sojourner

2

Security and Networking / Wpa-psk And 3.5.4

« on: April 06, 2006, 06:30:11 pm »

Have you submitted a bug or asked on the openzaurus mailing lists?

I know nothing about this subject, a bug or mailinglist question will get you far more exposure to the OZ devs.


Si
[div align=\"right\"][a href=\"index.php?act=findpost&pid=122005\"][{POST_SNAPBACK}][/a][/div]

Thanks for the tip lardman, didn't even think of it.

nax: thanks for submitting the bug.

Best regards,

-sojourner

3

Security and Networking / Wpa-psk And 3.5.4

« on: April 05, 2006, 11:42:32 pm »

Looks like I'll have to go back to 3.5.3:

TuxMobil

The card no longer works with 3.5.4

I'd be willing to test changes to the hostap drivers in order to get this to work if any developers have time to mess with them.

-sojourner

4

Security and Networking / Wpa-psk And 3.5.4

« on: April 05, 2006, 03:43:40 am »

Just flashed to Opie 3.5.4 using the 32-32 zImage on my collie and everything looks great with the exception of WPA-PSK CCMP on my Ambicom WL1100C.

I'm using the same wpa_supplicant.conf I used under 3.5.3 with no problems. I wrestled with it for a few hours and flashed back to 3.5.3 just to see if I missed something but after flashing and immediately starting up the wpa_supplicant in debug mode (hostap) it connected up with no issues. I did not need to make any changes under 3.5.3.

Flashed back to 3.5.4 and still no go. Disabling encryption works fine on 3.5.4 with this card but that isn't an option.

Any ideas out there? I've searched high and low to no avail.

Here is what i get from running "wpa_supplicant -Dhostap -iwlan0 -c/etc/wpa_supplicant.conf -dd":

Code: [Select]

Priority group 1
   id=0 ssid='lamessid'
wpa_driver_hostap_set_wpa: enabled=1
wpa_driver_hostap_set_key: alg=none key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_countermeasures: enabled=0
wpa_driver_hostap_set_drop_unencrypted: enabled=1
 
Setting scan request: 5 sec 0 usec
Starting AP scan (broadcast SSID)
Wireless event: cmd=0x8b19 len=12
Received 233 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 1
0: 00:00:00:00:06:22 ssid='lamessid' wpa_ie_len=0 rsn_ie_len=0
   skip - no WPA/RSN IE
No suitable AP found.
Setting scan request: 5 sec 0 usec
Starting AP scan (broadcast SSID)
Wireless event: cmd=0x8b19 len=12
Received 233 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 1
0: 00:00:00:00:06:22 ssid='lamessid' wpa_ie_len=0 rsn_ie_len=0
   skip - no WPA/RSN IE
No suitable AP found.
Setting scan request: 5 sec 0 usec
Starting AP scan (broadcast SSID)
Wireless event: cmd=0x8b19 len=12
Received 233 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 1
0: 00:00:00:00:06:22 ssid='lamessid' wpa_ie_len=0 rsn_ie_len=0
   skip - no WPA/RSN IE
No suitable AP found.
Setting scan request: 5 sec 0 usec
Signal 2 received - terminating
wpa_driver_hostap_set_key: alg=none key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_wpa: enabled=0
wpa_driver_hostap_set_drop_unencrypted: enabled=0
wpa_driver_hostap_set_countermeasures: enabled=0
Same command and config works under 3.5.3

wpa_supplicant.conf looks like this:

Code: [Select]

ctrl_interface=/var/run/wpa_supplicant
ctrl_interface_group=0
eapol_version=1
ap_scan=1
network={
   ssid="lamessid"
   proto=WPA
   psk="somelamepassphrase"
   key_mgmt=WPA-PSK
   pairwise=CCMP
   group=CCMP
   priority=1
}
Regards,

-sojourner

5

Angstrom & OpenZaurus / Oz 3.5.3 - Strange Behaviour W/ Sharp-compat-libs

« on: April 18, 2005, 12:59:26 am »

Has anyone else noticed this problem yet?  (BUMP)
[div align=\"right\"][a href=\"index.php?act=findpost&pid=75700\"][{POST_SNAPBACK}][/a][/div]

Yes, just installed Gutenbrowser 1.5.4 from the SourceForge page and encountered the same behavior.

-- sojourner

6

Angstrom & OpenZaurus / 3.5.3 Upgrades

« on: April 17, 2005, 11:55:30 am »

I installed qpegps, but it requires a gpsd to run...and gpsd isn't in the feed.
...
[div align=\"right\"][{POST_SNAPBACK}][/a][/div]

gpsd is in the /net feed.
[a href=\"http://www.openzaurus.org/official/unstable/3.5.3/feed/net/]http://www.openzaurus.org/official/unstable/3.5.3/feed/net/[/url]

-- sojourner

7

Angstrom & OpenZaurus / Oz3.5.3 (collie) On/off Button Problem

« on: April 16, 2005, 10:46:03 am »

Looks like it's working here too. :-D

Thanks Cwiiis!

-- sojourner

8

Angstrom & OpenZaurus / Oz3.5.3 (collie) On/off Button Problem

« on: April 15, 2005, 10:44:12 pm »

This 'fix' has been applied in the gpe-image for collie handhelds only - if you have problems resuming after suspend, try this:

-Remove the line containing /dev/apm_bios from /etc/device_table
-Reboot
...
[div align=\"right\"][a href=\"index.php?act=findpost&pid=75463\"][{POST_SNAPBACK}][/a][/div]

Thanks for the info. I just made the change and will let everyone know how it goes...

-- sojourner

9

Angstrom & OpenZaurus / 3.5.3 Upgrades

« on: April 15, 2005, 07:15:04 pm »

A working Wellenreiter II would be nice

Thanks to all the effort the OZ and Opie teams put in! It is much appreciated.

-- sojourner

10

Angstrom & OpenZaurus / Oz3.5.3 (collie) On/off Button Problem

« on: April 15, 2005, 09:24:20 am »

...
I can confirm that this bug exists.  Not all the time but whenever it has been swithced off for a while.
Everything flashed okay as far as I know.
[div align=\"right\"][a href=\"index.php?act=findpost&pid=75346\"][{POST_SNAPBACK}][/a][/div]

Ok, after my first post on this yesterday I am now seeing this every time I suspend. Not sure what the issue is. OZ 3.5.3 32-32 zImage w/Opie, md5sums checked out fine.

-- sojourner

11

Angstrom & OpenZaurus / Oz 3.5.3 Wellenreiter Ii -- We V16/we V17

« on: April 14, 2005, 09:12:29 pm »

With OZ 3.5.3 (opie) on collie (SL5500) I am seeing a problem similar to this one with Wellenreiter:
wellenreiter II - opie 1.1.4 - oz 3.3.6-pre1

Only it is complaining about WE V16 (for the interface driver) and WE V17 (for Wellenreiter II). I am using the 32-32 zImage and my wireless card is an AmbiCom WL100C-CF (hostap), if that is of any help.  

* Wellenreiter from the OpenZaurus 3.5.3 feed: opie-wellenreiter_1.2.0-r0_arm.ipk
* Wellenreiter version number when running: V1.0.3 (unofficial)

Wellenreiter was working rather nicely with 3.5.2; same WiFi, same SL5500. Is this the same problem as the linked post or the same symptom/different problem?

-- sojourner

12

Angstrom & OpenZaurus / Oz3.5.3 (collie) On/off Button Problem

« on: April 14, 2005, 10:30:04 am »

When I press the on/off button, collie goes to sleep but won't wake up again unless I flip the "replace battery" switch.
...
[div align=\"right\"][a href=\"index.php?act=findpost&pid=75135\"][{POST_SNAPBACK}][/a][/div]

I saw this yesterday with 3.5.3 after installing a number of packages but it woke up fine this morning.

-- sojourner

13

Angstrom & OpenZaurus / Opie Todo Sync With Qtopia Desktop

« on: April 06, 2005, 03:47:25 pm »

When I sync the latest Opie with Qtopia desktop the Description field is blank when viewed in Qtopia desktop. Could someone please explain to me why this incompatibility was introduced?
...
[div align=\"right\"][a href=\"index.php?act=findpost&pid=73839\"][{POST_SNAPBACK}][/a][/div]

"latest Opie" as in 3.5.2 or the pre-release 3.5.3?

Which version of Qtopia Desktop? I have the 1.7 RedHat version working just fine under Slackware-current (10.1 updated to -current 3/26/05 updates) with Opie 3.5.2.

-- sojourner